Jacuzzi LED Series User Manual

9
4.4 Programming Filter Cycles (2011-2012 J200 models equipped with a circulation
pump)
To select a pre-programmed lter cycle or lockout mode, press and hold both control panel
WARMER and COOLER buttons at the same time, then release. Then press either WARMER or
COOLER buttons to select either lter mode F0 through L2 below:
Standard Mode
F0 5 minutes of ltration per day (one 5 minute “Blow-Out” cycle every 24 hours to purge all plumbing lines.
F1 1 hour of ltration per day (one 30-minute cycle every 12 hours); this is the factory default setting.
F2 1.5 hours of ltration per day (one 30-minute cycle every 8 hours).
F3 2 hours of ltration per day (one 30-minute cycle every 6 hours).
Economy Mode
F4 1 hour of ltration/heating per day (one 30-minute cycle every 12 hours).
F5 1.5 hours of ltration/heating per day (one 30-minute cycle every 8 hours).
F6 2 hours of ltration/heating per day (one 30-minute cycle every 6 hours).
Lock Mode
L1 Lock Out (disables all hot tub functions to permit lter cleaning) - If hot tub is heating when the system is
put into lockout mode, the heater will immediately turn off and the pump will cycle water for 30 seconds to
cool heater element, then turn off.
L2 Lock Mode (disables the jets and light buttons to prevent unauthorized use of the hot tub) - lter cycles and
heater will continue to operation as programmed in this mode. The temperature display ashes when this
function is enabled. Example: The “F3” lter cycle was enabled prior to choosing lock mode. The hot tub
continues to perform lter cycle “F3” until lock mode is canceled, allowing another lter cycle to be selected.
4.5 Programming Filter Cycles (2013+ J200 models not equipped with a circulation
pump)
To select a pre-programmed lter cycle or lockout mode, press and hold both control panel
WARMER and COOLER buttons at the same time, then release. Then press either WARMER or
COOLER buttons to select either lter mode F1 through L2 below:
Standard Mode
F1 4 hours of ltration a day (2 hour cycle every 12 hours): this is the factory default setting.
F2 6 hours of ltration a day (2 hour cycle every 8 hours)
F3 8 hours of ltration a day (2 hour cycle every 6 hours)
Economy Mode
F4 4 hours of ltration a day (2 hour cycle every 12 hours)
F5 6 hours of ltration a day (2 hour cycle every 8 hours)
F6 8 hours of ltration a day (2 hour cycle every 6 hours)
Lock Mode
L1 Lock Out (disables all hot tub functions to permit lter cleaning).
Note: The spa should not be left in this lock mode for an extended period of time. Especially in colder climates
or when freezing conditions exist.
L2 Lock Mode (disables the jets buttons to prevent unauthorized use of the hot tub) ltration/heating cycles
and heater will continue to operation as programmed in this mode. The temperature display ashes
when this function is enabled. Example: The “F3” lter cycle was enabled prior to choosing lock mode.
The hot tub continues to perform lter cycle “F3” until lock mode is canceled, allowing another lter
cycle to be selected.
L3* Lock Mode (disables the temperature up and down buttons to prevent unauthorized temperature
adjustments). Filtration/heating cycle will continue to operate as programmed in this mode. The jets and
lights buttons will still continue to operate as normal. The temperature display ashes when this function
is enabled. *Due to a difference in software this feature is not available for all models, started in 2014.
Note: To exit a Lock Mode you will need to re-enter the ltration/heating modes and select a cycle from F0-F6.

Jacuzzi LED Series Specifications

General

Brand	Jacuzzi
Model	LED Series
Category	Hot Tub
Language	English