Why is there no sound coming from my JAMO Receiver?
If you're not getting any sound from your JAMO Receiver, there are a couple of things to check: First, make sure the volume isn't set to 0; if it is, simply turn up the volume. Second, ensure that the speaker cables are correctly connected. If they aren't, connect them properly.
How to fix no picture on my JAMO Receiver?
If you are experiencing a 'no picture' issue with your JAMO Receiver, here's what you can do: First, ensure that the TV is switched ON. If it is already ON, then check if the TV is correctly connected to the receiver and connect it correctly if needed.
What to do if JAMO Receiver DMR 70 remote control not working?
If your JAMO Receiver DMR 70 isn't responding to the remote, here are a few things to try: 1. Make sure that batteries are inserted in the remote control. If not - insert new batteries. 2. If batteries are inserted, they may be worn out, replace them with new ones. 3. Ensure that you are pointing the remote controller at the remote sensor of the DMR 70. 4. Make sure that you are operating the remote controller within 5 m.
Why my JAMO DMR 70 has no power even when plugged in?
If your JAMO Receiver isn't getting power even when plugged in, check these two things: * Ensure the power plug is securely connected. * Verify the wall plug is turned ON.
What to do if my JAMO Receiver can't play a disc?
If your JAMO Receiver is unable to play a disc, consider the following: * Ensure the disc label is facing up. * The disc may be empty or its format might not be supported by the DMR 70. In this case, remove the disc and try another. * The disc may be dirty or defective. Try cleaning it, or dispose of it if necessary. * Make sure the disc is placed within the proper guide on the disc tray.
Why JAMO Receiver DMR 70 not responding to some commands during playback?
The DMR 70 may not respond to some operating commands during playback because operations may not be permitted by the disc. Read the instructions on the disc.
Why is there no sound from my JAMO DMR 70?
If there is no sound, ensure that the VOLUME is not set to 0. If it is, turn up the VOLUME. Also, check that the speaker cables are connected correctly and connect them correctly if needed.
What to do if my JAMO Receiver DMR 70 unit does not respond to the remote control?
If the DMR 70 unit isn't responding to the remote, first check if batteries are inserted in the remote control, and insert new batteries if needed. If batteries are already in place, try replacing them with new ones. Ensure that you are pointing the remote controller at the remote sensor of the DMR 70, and that you are within 5 meters of the DMR 70.
How to fix a JAMO DMR 70 when there is no picture?
If there is no picture, ensure that the TV is switched ON. If it is OFF, turn it ON. Also, verify that the TV is connected correctly, and if not, connect the TV correctly.
What to do if power is not supplied to my JAMO DMR 70 Receiver?
If power is not being supplied to your device, even with the power cable connected, make sure the power plug is securely connected. If it is not, connect the power plug securely. Also, check if the wall plug is turned ON, and if it is not, turn it ON.
Lists all accessories provided with the Jamo DMR 70 DVD receiver.
Diagram and description of rear panel ports for speakers, audio, video, and antennas.
Guides for SCART, S-Video, and Component/HDMI video setup with various source devices.
Configuration settings for disc lock, display brightness, VOD code, PBC, memory, and defaults.
Customization of OSD, DivX subtitles, audio, and menu languages.
Adjusting speaker size, delay, digital/HDMI audio output, and performing speaker tests.
Setting TV type, display aspect ratio, progressive scan, HDMI, and component video.
Instructions for manual and automatic searching, storing, and RDS service use.
To Next Page
General
