Jardine Madison DA833BC - User Manual

Model # DA833BC- Madison Single Crib (Natural)
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Follow warnings on all products in a crib.
*
*
*
*
*
*
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model number, color
and a detailed description of the part.
Before each usage or assembly, inspect crib for damaged hardware, loose joints, missing parts or
sharp edges, DO NOT use crib if any parts are missing or broken. Ask your dealer or write to our
customer service representative (address & phone number shown above) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be
used.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless otherwise advised by your physician.
E-MAIL: csr@jardcoent.com
WARNING
Failure to follow these warnings and assembly instructions could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged or loose (if teething rail is provided for this model).
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Strings can cause strangulation! DO NOT place crib with a string around a child's neck, such as hood
strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
If refinishing, use a non-toxic finish specified for children's products.
Assemble on soft, smooth surface to prevent damage to product finish.
Phillips head screw driver is not included.
DO NOT use power tools.
CAUTION: Adult assembly required.
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4 INCHES BY 51-5/8
INCHES (69CM BY 131CM) WITH A MINIMUM THICKNESS OF 4 INCHES (10CM) BUT NOT
EXCEEDING 6 INCHES (15CM).
Infants can suffocate in gaps between crib sides and a mattress that is too small.
NOTES
Ensure all parts and components are present before beginning assembly.
Assembly will require two people.

Summary

Safety and Usage Warnings

General Safety Precautions

Covers general warnings for assembly, suffocation, strangulation, crib usage limits, and placement.

Mattress and Suffocation Hazards

Details specific mattress size requirements and risks of suffocation from gaps.

Assembly Preparation

Pre-Assembly Checks and Tools

Ensures parts are present, specifies assembly surface, tools, and manpower requirements.

Product Care and Maintenance

Cleaning and Storage Guidelines

Instructions for dusting, cleaning with a damp cloth, avoiding abrasives, and proper storage.

Periodic Maintenance Checks

Advises on regularly checking and tightening bolts and screws.

Warranty Information

Assembly Instructions

Hardware and Parts List

Identifies and lists all necessary hardware and crib components for assembly.

Step-by-Step Assembly Guide

Detailed instructions for assembling the crib, including attaching posts, sides, and support.

Drop Side Operation

Instructions for installing and operating the drop side mechanism safely.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features
5. Customer Service and Warranty

This document is a user manual for the DA833BC Madison Single Crib (Natural). It provides essential information for assembly, safe usage, maintenance, and customer service.

Function Description:

The DA833BC Madison Single Crib is a piece of nursery furniture designed to provide a safe sleeping environment for infants. It features a stationary side and a drop side for ease of access to the child. The crib is designed to accommodate a mattress and includes a mattress support with adjustable height positions.

Important Technical Specifications:

• Model Number: DA833BC
• Product Name: Madison Single Crib (Natural)
• Mattress Dimensions: Must be at least 27-1/4 inches by 51-5/8 inches (69cm by 131cm).
• Mattress Thickness: Minimum of 4 inches (10cm) but not exceeding 6 inches (15cm).
• Maximum Child Height: The crib should no longer be used when the child is able to climb out or reaches the height of 35 inches (90 cm).
• Hardware: Includes various bolts (5"x1/4"DIA, 3 1/4"x1/4"DIA, 2"x1/4"DIA), mattress support bolts (1/2"x1/4"DIA), machine screws (0.3805"x0.1785"DIA), an Allen wrench (4MM), rubber bumpers, and a stabilizing bar.
• Components: Consists of left and right end panels, a stationary side, a drop side, left and right back posts, left and right front posts, and a mattress support.

Usage Features:

• Assembly: Requires adult assembly, preferably by two people. Instructions specify turning screws clockwise until tight, then loosening 1/2-3/4 of a turn, and re-tightening after full assembly. Wax or soap can be used on screws to facilitate assembly.
• Drop Side Operation: The drop side is operated by standing at the middle, holding the top rail, raising it slightly, and pushing on the lower rail with a knee to release the latch. Raising the drop side will automatically lock it in the upper position. Users must ensure the drop side is properly secured.
• Mattress Height Adjustment: The mattress support has 4 position holes, allowing for adjustable mattress height. When the child is able to pull to a standing position, the mattress should be set to the lowest position. All height adjustment holes must be filled with appropriate bolts after moving the mattress support.
• Safety Warnings:
  • Failure to follow warnings and instructions can result in serious injury or death.
  • Read all instructions before assembly and keep them for future use.
  • Inspect the crib before each use for damaged hardware, loose joints, missing parts, or sharp edges. Do not use if any parts are missing or broken.
  • Do not substitute parts.
  • Never add a pillow or comforter, or place additional padding under an infant, as infants can suffocate on soft bedding.
  • To reduce the risk of SIDS, place healthy infants on their backs to sleep.
  • Do not place the crib near a window where cords from blinds or drapes may strangle a child.
  • Do not place strings around a child's neck or suspend strings over the crib, as strings can cause strangulation.
  • Tighten all fasteners to prevent body parts or clothing from getting trapped.
  • If refinishing, use a non-toxic finish specified for children's products.
  • Remove bumper pads, large toys, and other objects that could serve as steps for climbing out when the child can stand.
  • Never use plastic shipping bags or film as mattress covers due to suffocation risk.
  • Do not use a water mattress.
  • Replace teething rail if damaged or loose.
  • Ensure the mattress fits snugly to prevent suffocation in gaps.
  • Follow warnings on all products used in the crib.
  • If the product becomes damaged, or components are broken or missing, DO NOT USE.
• Mattress Support Installation: Tabs on the mattress support must always be above the mattress support, and the flat surface of the mattress support should face up for the mattress to sit on a flat surface.

Maintenance Features:

• Cleaning: Dust regularly with a soft, lint-free cloth. A damp cloth may be used occasionally; dry immediately. Do not use abrasives.
• Hardware Check: Check bolts/screws periodically and tighten them as necessary.
• Storage: If storing the crib, keep it in a cool, dry place and carefully package all original hardware to prevent loss.
• Teething Rail: Ensure the teething rail is on top when installing stationary and drop sides. Replace if damaged or loose.
• Environmental Considerations: Excessive exposure to sunlight and extreme changes in temperature and moisture can damage wood furniture.

Customer Service and Warranty:

• Missing Parts/Questions: Contact customer service at 1-800-295-1980 or by email at csr@jardcoent.com.
• Ordering Parts: Parts can be ordered by writing to Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, Quebec, Canada H1G 3L1. Include the product model number, color, and a detailed description of the part.
• Limited Warranty: Jardine Enterprise warrants the product to be free from defects in material and workmanship for 1 year from the original purchase date. The warranty requires proof of purchase and is limited to the repair or replacement of defective furniture components, excluding assembly labor. It does not cover products improperly assembled, misused, abused, altered, or repaired. This warranty provides specific legal rights, which may vary by state.

Jardine Madison DA833BC Specifications

General

Brand	Jardine
Model	Madison DA833BC
Category	Baby & Toddler Furniture
Language	English