JBL VRX932LAP/230 User Manual

JBL Incorporated, 8500 Balboa Boulevard, P.O. Box 2200, Northridge, California 91329 U.S.A.
JBL VRX932LAP/230 REV M
PACKAGE
08-12
Technical Manual
JBL VRX932LAP/230
SPECIFICATIONS
ACOUSTIC & ELECTRICAL SPECIFICATIONS:
• DPC-2 Internal Amplification Output
(at normal load): 1750 Watts Peak, 875 Watts Continuous
• Frequency Response: 75 Hz - 20 kHz (±3 dB)
• Frequency Range: 57 Hz - 20 kHz (–10 dB)
• Maximum Peak Output: 136 dB SPL at 1m
• Signal Processing: DSP based, resident in Input Module
• AC Power Operating Range: 90-132 VAC or 216-264 VAC, 50/60Hz
• AC Input Connector: Neutrik PowerCon (NAC 3MPA)
• AC Loop Through Connector: Neutrik PowerCon (NAC 3MPB)
• Audio Input Connector: XLR with loop through
• AC Current Requirements: 6A per system at 120V, 3A per system
at 240V
• AC Line Voltage: User selectable:120V/240V (-15%,+10%)
• System Managerment: DSP based limiters for mechanical and
thermal protection
• User Controls: Input Attenuator (0-16 dB), ACS Array
Configuration Selector), HF level adjust-
ment (+3 dB, 0 dB, –3 dB)
• DPC-2 Output as (Continuous IEC shaped pink noise into rated load
impedance): LF:750 Watts, HF: 125 Watts
• DPC-2 Output section LF: Dual-Bridged Technology
(TM)
,Class D
HF:Bridged Class D
SYSTEM COMPONENTS:
• Cabinet: Enclosure (Not For Sale)
• Grille: 352282-001
• Low Frequency 2262FF, 305 mm (12 in) dual voice coil
Transducer: Differential Drive
(R)
woofer with neo-
dymium-magnet
• Bandpass Nominal
Inpedance: 2 x 2 ohms
• DC Resistance: 5.1 ohms ± 10%
• High Frequency (3) 2408J, 38 mm (1.5 in) voice coil,
Transducer neodymium compression driver
• Bandpass Nominal
Inpedance: 4 ohms
• DC Resistance: 8.9 ohms ± 0.2%
AURAL SWEEP TEST SPECIFICATIONS:
A. System Aural Sweep Test: 0.8V (Gain fully CCW)
B. L.F. Aural Sweep Test: 7V Input, 10 Hz to 1 kHz
C. H.F. Aural Sweep Test: 1.0V Input, 200 Hz to 1.5 kHz
PHYSICAL SPECIFICATIONS:
• Enclosure Dimensions: 349 x 597 x 444 mm D
(13.75 x 23.5 x 17.5 in. D)
• Net Weight: 52 lb (24 kg.)
WARRANTY INFORMATION:
• Refer to Warranty Statement packed with each product.
Warranty 59660
Carton
364342-001
Driver,
Low Freq
2262FF
(363946-001X)
Cone Repl
C2X2R2262
Driver,
High Freq (3)
2408J
(361549-003X)
Diaph Repl
D16R2408
Amplifier
Assemby
DPC-2
Wire Harness
Assembly
364338-004
WIRING DIAGRAM
Power Cord Assembly
Pack / Edison, Shucko
355040-002
Contents:
355146-001 (120V) (1)
Power Cord
355147-001 (230V) (1)
Power Cord
NAC3FCB (1)
Neutrik
Gray PowerCon
Manual
364536-001
Pad, Filler (2)
364343-001
Filler, Grille
364344-001
Pkg, Microfoam
49790P
LF-1
LF-2
LF-1
LF-2
GRN/BLK
GRN
BLU
BLU/BLK
YEL/BLK
YEL
WIRING HARNESS DIAGRAM / SCHEMATIC
364338-004
GRN/BLK
BLU/BLK
YEL/BLK
BLU
GRN
YEL
NOT USED
NOT USED
26.5” YEL/BLK
26.5” YELLOW
20.5”GRN/BLK
20.5” GRN
20.5” BLU/BLK
20.5” BLU
.250 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
.187 SERIES,RECEPTABLE/TAB FASTON PIGGYBACK
SCHEMATIC

JBL VRX932LAP/230 Specifications

General

Frequency Range (-10 dB)	45 Hz - 20 kHz
Power Handling	1000 W
LF Driver	12"
HF Driver	1.5"
Amplifier	Class D
Input Connectors	XLR
Output Connectors	Neutrik NL4
Dimensions (H x W x D)	23.5" x 14.5" x 14.5" (597mm x 368mm x 368mm)
Enclosure Material	Plywood

Summary

JBL VRX932LAP/230 Specifications

Acoustic and Electrical Specifications

Details output, frequency response, impedance, and power requirements for the speaker system.

System Components

Lists the components included in the package and their part numbers.

Aural Sweep Test Specifications

Provides voltage and frequency input requirements for sweep tests.

Physical Specifications

Outlines enclosure dimensions and net weight of the unit.

Package Contents

Wiring Diagrams

Wiring Harness Diagram and Schematic

Component Exploded View

Amplifier Assembly Details

Array Frame Assembly