How to troubleshoot no power on my Jensen Marine Equipment?
If your Jensen Marine Equipment has no power, there are a couple of things to check: * First, if the power supply is connected to the vessel accessory terminal, ensure the ignition key is switched to 'ACC'. * Second, inspect the fuse and replace it if it's blown.
Why is there no sound coming from my Jensen Marine Equipment?
If you're not getting any sound from your Jensen Marine Equipment, here's what you can check: * Make sure the volume isn't set too low and adjust it to a level you can hear. * Also, verify that all the wiring connections are properly connected.
What to do if my Jensen Marine Equipment cannot tune to radio station or auto-seek doesn't work?
If your Jensen Marine Equipment is having trouble tuning to radio stations or the auto-seek function isn't working, consider the following: * Ensure the antenna cable is firmly inserted. * If the signals are too weak, try selecting a station manually.
What to do if disc cannot be loaded or ejected from Jensen Marine Equipment?
If you're having trouble loading or ejecting a disc from your Jensen Marine Equipment, here are a few things to try: * If there is a CD disc inside the player, remove the disc and insert the new one. * Make sure you're inserting the compact disc with the label facing upward. * If the disc is dirty or defective, clean it or try a new one. * If the temperature inside the vessel is too high, wait until it returns to normal. * If condensation has formed, leave the player off for about an hour, then try again.
Why does the sound skip on my Jensen Marine Equipment?
If the sound is skipping on your Jensen Marine Equipment, here are a couple of potential causes: * The installation angle might be more than 30 degrees. Adjust the installation angle to less than 30 degrees. * The disc could be dirty or defective. Clean the disc and try playing it again, or try a new disc.
What to do if the operation keys do not work on Jensen Marine Equipment?
If the operation keys on your Jensen Marine Equipment aren't working, it could be due to noise affecting the built-in microcomputer. Try pressing the reset button (17).
General| USB Port | Yes |
|---|---|
| Water Resistant | Yes |
| AM/FM Radio | Yes |
| Tuner | AM/FM |
| Weatherband | Yes |
| Auxiliary Input | Yes |
| Waterproof | No |
| Display | LCD |
| Category | Marine |
Advice on maintaining situational awareness while operating the vessel.
Instructions to prevent electrical shorts, fire, or damage from water exposure.
Guidance on avoiding damage from high temperatures and direct sunlight.
Specifies the requirement for a 12-volt DC negative ground battery system.
Warnings against inserting foreign objects into the disc slot.
Information on supported disc types and playback time.
Guidelines for cleaning and handling discs to ensure proper playback.
Initial steps including disconnecting the battery and removing transport screws.
Crucial considerations before and during installation.
Step-by-step guide for mounting the unit in a dashboard opening.
Procedure for safely removing the unit from its mounting.
Instructions for fitting the trim plate to the chassis.
Final step to reconnect the battery after all wiring is complete.
Diagram illustrating the antenna connection point.
Detailed view showing wire insertion into the connector.
Table mapping pin numbers to wire colors and their functions.
Procedure for turning the unit on and off.
Instructions for adjusting the audio volume level.
How to mute and restore audio output.
Selecting different operational modes like Tuner, CD, or AUX IN.
Applying preset sound effects to the audio output.
Boosting bass and treble at low volume levels.
Connecting and operating external audio/video systems via AUX IN.
Accessing and adjusting audio settings like Bass, Treble, Balance, Fader.
Procedure for setting the unit's clock time.
How to reset the unit to factory default settings.
Scanning and pausing at preset stations for eight seconds.
Automatic detection and indication of stereo signals.
Selecting signal strength for automatic tuning.
Switching between USA and European broadcast tuning regions.
Changing between FM and AM bands to access stored stations.
Adjusting radio frequency one step at a time.
Automatically tuning to the next available station.
Saving a tuned station to a preset button.
Recalling a previously stored station.
Automatically selecting and storing six strong stations.
Instructions for inserting and ejecting CDs.
Advancing to the next track or skipping ten tracks.
Suspending and resuming disc playback.
Previewing the first 10 seconds of each track.
Repeating the current track during playback.
Playing all tracks on a CD in a random order.
Technical specifications related to CD playback.
Technical specifications for the FM radio tuner.
Technical specifications for the AM/MW radio tuner.
General operating and electrical specifications.
Solutions for issues where the unit does not power on.
Troubleshooting steps for problems with disc insertion or ejection.
Solutions for situations where there is no audio output.
Troubleshooting for unresponsive control buttons.
Solutions for problems causing audio playback to skip.
Fixes for issues with radio tuning and auto-seek functionality.
Troubleshooting steps for specific error code 1.
Troubleshooting steps for specific error code 2.
To Next Page