Jet ProShop JPS-10 User Manual

JPS-10: 10" PROSHOP 1-3/4HP 30"- CW
The JET ProShop 10" Table Saw (#708482K) is the
result of combining key cabinet saw features with the
semi open leg structure of the venerable contractor-
style table saw. While developing a unique set of
technologies to give the JET ProShop 10" Table Saw
wide-ranging capabilities was the goal, accuracy,
durability and ease of use remained at the top of the
priority list throughout the design process.
This new design also allowed simplifying the assembly
process considerably. With the motor installed within
the cabinet at the factory, the process of hanging the
motor on an external bracket and aligning it with the
arbor, common on contractor-style saws is eliminated completely. The extended
cabinet of the JET ProShop 10" Table Saw also replaces the open leg assembly
common contractor saws with four channel-shaped legs that are extremely rigid and
very easy to install. Four bolts secure each leg to the cabinet and need only to have
the leveling feet attached to get the JET ProShop 10" Table Saw upright and ready
for final assembly.
The new JET JPS-10 ProShop saw
represents new thinking that
makes your shop time more
accurate and productive
.
At the heart of the JET ProShop 10" Table Saw is the all-new operating mechanism
that locates the motor inside of the cabinet. This massive cast iron mechanism is
extraordinarily rigid and substantially increases the vibration dampening mass
directly below the
table. The result is
super smooth, super
quiet operation with
an overall stability of
the blade system
previously found
only in machines
that are far more
expensive.
A dual drive belt
system transfers
motor power to the
5/8”-diameter arbor that is located in a short, super rigid cast iron arm. Blade height
adjustments are remarkably smooth in part because the blade arm is isolated from
the weight of the motor and undercarriage. The 5/8”-diameter arbor was designed
with sufficient length to handle most stacked 6” or 8”-diameter dado sets at a full
13/16” width.
The all-new ProShop mechanism (left) not only moves the motor inside of
the cabinet but also uses a heavy-duty swing arm (right) to locate the
arbor. This system drastically reduces vibration and makes blade height
changes smooth and precise.
The blade height and tilt mechanism provides maximum cut depths of 3 1/8” at 0-
degrees and 2 1/8” at 45-degrees. The mechanism tilts the blade to the left, away
from the fence so the operator is controlling the major piece and the scrap falls onto
the table, away from the blade.

Jet ProShop JPS-10 Specifications

General

Brand	Jet
Model	ProShop JPS-10
Category	Saw
Language	English

Summary

JET ProShop 10" Table Saw Introduction

Design Philosophy and Capabilities

Combines cabinet saw features with contractor-style leg structure, prioritizing accuracy, durability, and ease of use.

Simplified Assembly and Cabinet Structure

Features a pre-installed motor and four rigid channel-shaped legs for straightforward assembly and stability.

Core Mechanism and Vibration Dampening

Houses a massive, rigid cast iron mechanism directly below the table for superior stability and vibration dampening.

ProShop Mechanism Operation

Uses a heavy-duty swing arm to locate the arbor, ensuring smooth, precise blade height changes and reduced vibration.

Arbor and Blade Tilt Features

Features a 5/8" arbor accommodating dado sets and a tilt mechanism for precise depth cuts and safe scrap handling.

Enhanced Usability and Performance Features

Convenient Blade Changing

Features a pushbutton arbor lock integrated into the table surface for easier blade changes.

Accessible Bevel Adjustments

Bevel stop adjusters are moved to the exterior for easier fine-tuning of blade tilt stops.

Powerful and Protected Motor

Powered by a 1 3/4 Hp TEFC motor with thermal protection and a user-accessible reset button.

Integrated Dust Collection System

Allows for effective dust collection with a special cabinet floor and a rear cover with a 4" hose connection.

Robust Fence System Design

Built with a heavy gauge steel tube and T-square-style base for stability and smooth gliding.

Table and Miter Gauge Details

Precise Fence Cursor and Scale

Features a magnifying cursor on the T-square fence base for easy and accurate cut width settings.

Stable Fence Mounting System

Supported by heavy steel rails and a guide tube with an adjustable height pad for smooth operation.

Table Surface and Extension Wings

20"x27" cast iron table surface, expandable to 44"x27" with optional steel or cast iron extension wings.

Miter Slots and Accessories

Precision-milled T-style miter slots accept common table saw accessories for versatile use.

Adjustable Miter Gauge

Includes an angle-adjustable miter gauge with a guide bar for precise, wobble-free cuts up to 60 degrees.

Safety and Customization Options

Heavy-Duty Paddle Switch

Features a large, paddle-style On/Off switch for easy activation by hand or leg.

Customizable Configurations

Available with 30" or 50" fence systems, with or without extension wings and router plates.