Jet JWBS-14 - User Manual

3
GB - ENGLISH
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been
prepared for the owner and operators of a JET JWBS-14 band saw to promote safety during installation, operation and
maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read this
manual thoroughly and follow instructions carefully.
…Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
Authorized use
General safety notes
Remaining hazards
4. Machine specifications
Technical data
Noise emission
Dust emission
Contents of delivery
5. Transport and start up
Transport and installation
Assembly
Mains connection
Dust connection
Starting operation
6. Machine operation
7. Setup and adjustments
Changing the saw blade
Blade tracking adjustment
Blade tension adjustment
Blade guide adjustment
Folding the bandsaw blade
8. Maintenance and inspection
9. Troubleshooting
10. Environmental protection
11. Available accessories
12. „Safe operation”........ appendix A
1. Declaration of conformity
On our own responsibility we hereby
declare that this product complies with
the regulations* listed on page 2.
Designed in consideration with the
standards**. CE type examination***
conducted by****.
2. Warranty
The Seller guarantees that the
supplied product is free from material
defects and manufacturing faults. This
warranty does not cover any defects
which are caused, either directly or
indirectly, by incorrect use,
carelessness, accidental damage,
repair, inadequate maintenance or
cleaning and normal wear and tear.
Guarantee and/or warranty claims
must be made within twelve months
from the date of purchase (date of
invoice). Any further claims shall be
excluded.
This warranty includes all guarantee
obligations of the Seller and replaces
all previous declarations and
agreements concerning warranties.
The warranty period is valid for eight
hours of daily use. If this is exceeded,
the warranty period shall be reduced
in proportion to the excess use, but to
no less than three months.
Returning rejected goods requires the
prior express consent of the Seller and
is at the Buyer’s risk and expense.
Further warranty details can be found
in the General Terms and Conditions
(GTC). The GTC can be viewed at
www.jettools.com or can be sent by
post upon request.
The Seller reserves the right to
make changes to the product and
accessories at any time.
3. Safety
3.1 Authorized use
This machine is designed for sawing
wood, wood derived materials as well
as similar to be machined hard
plastics only.
Machining of other materials is not
permitted and may be carried out in
specific cases only after consulting
with the manufacturer.
No metal workpieces may be
machined.
The proper use also includes
compliance with the operating and
maintenance instructions given in this
manual.
The machine must be operated only
by persons familiar with its operation
and maintenance and who are familiar
with its hazards.
The required minimum age must be
observed
The machine must only be used in a
technically perfect condition
When working on the machine, all
safety mechanisms and covers must
be mounted.
In addition to the safety requirements
contained in these operating
instructions and your country’s
applicable regulations, you should
observe the generally recognized
technical rules concerning the
operation of woodworking machines.
Any other use exceeds authorization.
In the event of unauthorized use of the
machine, the manufacturer renounces
all liability and the responsibility is
transferred exclusively to the operator.
3.2 General safety notes
Woodworking machines can be
dangerous if not used properly.
Therefore the appropriate general
technical rules as well as the following
notes must be observed.

Summary

Warranty

Safety

Authorized Use

Machine designed for sawing wood, wood derived materials, and hard plastics only. No metal workpieces.

General Safety Notes

Woodworking machines can be dangerous. Observe general technical rules and specific safety notes.

Machine Specifications

Technical Data

Details wheel diameter, cutting width/height, blade length/width/thickness, cutting speed, table size, tilting range, weight, mains, power, and reference current.

Noise Emission

Specifies acoustic power and pressure levels for idling and operating conditions as per EN standards.

Transport and Start Up

Transport and Installation

Instructions for safe transport using forklifts or trolleys and stable installation on firm ground.

Assembly

Steps for attaching the machinestand, table, support rails, and guide rail.

Mains Connection

Dust Connection

Starting Operation

Machine Operation

Setup and Adjustments

Changing the Sawblade

Procedure for changing the sawblade, including safety precautions and blade selection.

Blade Tracking Adjustment

How to adjust the sawblade to run on the center of the rubber tires for optimal performance.

Blade Tension Adjustment

Steps for adjusting the sawblade tension using the quick tension lever and handwheel.

Blade Guide Adjustment

Instructions for positioning the guide assembly and rollers for correct sawblade guidance.

Folding the Bandsaw Blade

Detailed steps on how to safely fold the bandsaw blade for storage or transport.

Maintenance and Inspection

Troubleshooting

Environmental Protection

Available Accessories

Safe Operation

Jet JWBS-14 Specifications

General

Brand	Jet
Model	JWBS-14
Category	Saw
Language	English