EasyManua.ls Logo

Jet JWBS-12OS - User Manual

Jet JWBS-12OS
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Operating Instructions and Parts Manual
12-inch Woodworking Band Saw
Model: JWBS-12OS
WMH TOOL GROUP, Inc
2420 Vantage Drive
Elgin, Illinois 60124 Part No. M-708901B
Ph.: 800-274-6848 Revision C 06/07
www.wmhtoolgroup.com Copyright © 2007 WMH Tool Group, Inc.
This Manual is Bookmarked

Table of Contents

Questions and Answers

  • K
    Kiara ProctorAug 1, 2025
    How to fix inaccurate cuts on my Jet JWBS-12OS?
    • D
      Deanna HarrisAug 1, 2025
      If your Jet Saw does not make accurate 45 or 90 degree cuts, it could be due to a few reasons. The table stop might not be adjusted correctly; check the blade with a square and adjust the table stop accordingly. Similarly, the angle pointer might not be set accurately, so check it with a square and adjust the pointer. Finally, the miter gauge could be out of adjustment, so adjust the miter gauge as needed.
  • D
    Dustin DunlapAug 5, 2025
    Why does my Jet JWBS-12OS Saw stop or not start?
    • B
      brandonellisAug 5, 2025
      If your Jet Saw stops or refuses to start, begin by checking all plug connections to ensure the saw is properly connected. If the connections are secure, inspect the fuse or circuit breaker. If the fuse is blown, replace it; if the circuit breaker has tripped, reset it. Finally, examine the cord for any damage. If the cord is damaged, it should be replaced.
  • T
    Tyler RodriguezAug 11, 2025
    What to do if my Jet JWBS-12OS Saw makes unsatisfactory cuts?
    • V
      Victoria WilliamsAug 11, 2025
      If your Jet Saw makes unsatisfactory cuts, several factors could be responsible. A dull blade is a common cause, so consider replacing it. Ensure the blade is mounted correctly, with the teeth facing the operator and pointing downwards. Check the blade and table for gum or pitch; if present, clean them with oven cleaner or another solvent. Finally, verify that you are using the correct blade type for the cut you are attempting.
  • T
    tthomasAug 15, 2025
    Why does the blade wander during cut on my Jet JWBS-12OS Saw?
    • S
      Stephanie RowlandAug 16, 2025
      If the blade of your Jet Saw wanders during a cut, there are several potential causes. First, check the fence alignment with the blade and adjust if necessary. If you're using warped wood, select a different piece. An excessive feed rate can also cause wandering, so try reducing it. Ensure you are using the correct blade for the type of cut you are making, and that the blade tension is properly set according to the blade size. Lastly, check and adjust the guides.
  • B
    Barbara MaysAug 21, 2025
    What to do if my Jet Saw vibrates excessively?
    • T
      Tyler RobinsonAug 21, 2025
      If your Jet Saw vibrates excessively, make sure the base is positioned on a flat, level surface. If the floor is uneven, reposition the saw. Also, check for any loose fasteners and tighten them.
  • P
    Peter CantrellAug 26, 2025
    Why doesn't the blade come up to speed on my Jet JWBS-12OS?
    • S
      Shannon LeeAug 26, 2025
      If the blade on your Jet Saw does not come up to speed, the extension cord may be too light or too long; replace it with a cord of adequate size and length. Another possibility is low shop voltage.

Summary

Warranty and Service

Warranty Details

Details product warranty durations, coverage, and exclusions for JET tools, including specific categories.

How to Get Service

Outlines the process for obtaining warranty service and repairs, including contact information and return procedures.

Warranty Limitations and Legal Rights

Details limitations on implied warranties and how state law may affect your specific legal rights.

General Safety Warnings

Safety Notice Definitions

Explains the meaning of CAUTION and WARNING symbols used throughout the manual for safety awareness.

Specifications

Unpacking and Assembly Preparation

Tools Required for Assembly

Lists the necessary tools and hardware for assembling the bandsaw and its stand.

Shipping Contents and Parts Identification

Assembly Instructions

Stand Assembly

Step-by-step guide for assembling the bandsaw stand using provided components.

Mounting Bandsaw to Stand

Instructions for attaching the saw body to the assembled stand securely.

Table Assembly Procedures

90° Table Stop Adjustment

How to adjust the table's 90-degree stop mechanism for accurate cuts.

Trunnion and Table Installation

Steps for installing the trunnion and securely mounting the table to the bandsaw.

Grounding and Electrical Safety

General Grounding Information

Importance and method of grounding the band saw to prevent electric shock.

115 Volt Operation Notes

Details on operating the saw with 115V power and necessary adapters for grounding.

Extension Cord Guidelines

Guidance on selecting appropriate extension cords for safe and efficient operation.

Operational Adjustments

Tilting the Table

How to adjust the table's tilt angle for various cuts, up to 45 degrees right or 5 degrees left.

Adjusting 90° Table Stop

Steps to set the table to a precise 90-degree angle for square cuts.

Changing Saw Blades

Procedure for safely replacing the saw blade, including precautions.

Blade Adjustment Procedures

Adjusting Blade Tension

How to properly tension the saw blade for optimal performance and to prevent breakage.

Adjusting Blade Tracking

How to align the blade on the wheels for correct tracking in the center.

Blade Guide Adjustments

Upper Blade Guide Positioning

How to set the upper blade guide height relative to the material being cut.

Blade Guide Block Adjustment

Aligning blade guide blocks correctly with the saw blade teeth for support.

Component Adjustments and Maintenance

Blade Support Bearing Adjustment

Setting the correct gap for blade support bearings to ensure proper blade guidance.

Adjusting V-Belt Tension

How to tension the drive belt for proper power transmission between pulleys.

Troubleshooting and Parts Information

Troubleshooting Common Issues

Identifies common band saw problems and provides practical solutions and remedies.

Ordering Replacement Parts

Instructions and contact information for ordering specific replacement parts for the band saw.

Accessories and Electrical Connections

Optional Accessories

Lists available optional accessories that can enhance the functionality of the band saw.

Electrical Connection Diagram

Shows the wiring diagram for the 115V motor connection, including switch and power supply.

Notes

Jet JWBS-12OS Specifications

General IconGeneral
TypeBandsaw
Motor Power1 HP
Cutting Capacity12 inches
Weight185 lbs
Blade Speed3000 FPM
Cutting Capacity Height12 inches
Cutting Capacity at 90°12 inches
Blade Length93.5 inches
Blade Width1/8 to 3/4 inches
Voltage115V
Table Tilt0 to 45 degrees

Related product manuals