To Next PageTo Next PageWhy does the weld break when used on my Jet VBS-1408 Saw?
If the weld breaks when used on your Jet Saw, it could be due to: * **Weak Weld:** Cut and re-weld blade ends. * **Overground Weld:** Cut and re-weld blade ends. * **Incorrect Annealing:** Follow annealing instructions.
How to fix cuts that are not straight on my Jet VBS-1408?
If your Jet Saw isn't cutting straight, it could be due to several reasons: * **Improper Blade Tooth Set:** File the blade to the correct set or replace it. * **Inadequate Blade Tension:** Increase the blade tension. * **Guide Post Too High:** Lower the guide post closer to the workpiece. * **Excessive Feed Rate:** Decrease the feed rate.
What causes a misaligned weld on my Jet VBS-1408 Saw?
If the weld on your Jet Saw is misaligned, consider the following: * **Contamination:** Keep jaws clean and clean blade before welding. * **Blade Ends:** Before welding, grind cut edges of blade until they are square. Use the shear on the band saw for square cuts. * **Misalignment:** Align ends properly before clamping. * **Worn Jaws:** Replace clamp jaws. * **Clamp Jaws:** Align jaws correctly.
What to do if my Jet Band Saw does not come up to speed?
If your Jet Band Saw does not reach its full speed, it may be caused by: * **Inadequate Extension Cord:** Replace the extension cord with one of adequate size and length. * **Low Current:** Contact a qualified electrician.
Why does the blade become damaged easily on my Jet Saw?
If the blade on your Jet Saw is easily damaged, consider the following: * **Over-Annealed Blade:** Decrease annealing temperature. * **Excessive Gap:** Adjust the gap between the blade guides and the blade. * **Inappropriate Blade Width:** Select a narrower blade appropriate to the job.
Why is my Jet Band Saw noisy, or vibrates too much?
If your Jet Band Saw is excessively noisy or vibrates too much, check the following: * **Unlevel Surface:** Ensure the band saw is resting on a flat floor. * **Damaged Pulley:** Replace the variable speed pulley.
Why do the blade teeth keep breaking on my Jet Saw?
If the blade teeth on your Jet Saw keep breaking, it may be due to: * **Incorrect Blade:** Select the proper blade pitch and style for the material you are cutting. * **Inferior Blade Material:** Use a better quality blade.
How to fix a twisted saw blade on my Jet VBS-1408 Saw?
If the saw blade on your Jet Saw is twisted, it could be due to: * **Improperly Welded Blade:** Re-weld the blade. * **Improper Blade Installation:** Set guide inserts closer, and increase blade tension. * **Excessive Force:** Decrease the feed rate. * **Incorrect Blade Choice:** Use the proper width blade for radius or wavy line cutting.
Why does the blade warp on my Jet VBS-1408?
If the blade on your Jet Saw is warping, consider the following: * **Dull Blade:** Sharpen or replace the blade. * **Improperly Fixed Guide Post:** Ensure the guide post is securely fixed in position. * **Insufficient Blade Tension:** Increase the blade tension. * **Misaligned Blade:** Adjust the table so it is perpendicular to the blade.
What to do if blade slips off wheel(s) on Jet VBS-1408 Saw?
If the blade on your Jet Saw keeps slipping off the wheels, it could be caused by: * **Inadequate blade tension:** Increase the blade tension. * **Wheels not aligned properly:** Contact technical service for adjustment of wheel alignment.
Essential safety guidelines for operating the band saw safely and preventing injury.
Explains the meaning of hazard symbols and warnings used in the manual.
Operate welder (weld, anneal) and grinder using dedicated buttons and switches.
Procedures for shearing blades and preparing teeth for welding.
Detailed steps for welding band saw blades and annealing them for proper temper.
Table of common operating issues and their solutions for the band saw.
Troubleshooting guide for mechanical failures and electrical problems, including motor and switch issues.
Guide to inspecting welded blade integrity, identifying misalignments, and breakages.
Addresses mechanical issues with the blade welder, such as jaw movement and annealing problems.
General
