JONATHAN Y Jayne JYL7545A

To Next Page

WARNING

WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.

WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT

BREAKER BEFORE INSTALLATION.

INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR

OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

CARE AND MAINTENANCE

To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe

the surface of the fixture.

To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the

fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the

interior surface of the fixture.

Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

NOTICE& IMPORTANT SAFETY INSTRUCTIONS

Model#: JYL7545A

Product Dimensions: 6''W X 9.5"H X 7"E

* Please make sure that you have all parts indicated before you begin assembly of this item

* This item should be assembled on a soft surface to prevent scratching the finish during assembly

* To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use

and installation

*The external flexible cable or cord of this lamp cannot be replaced

If the cord is damaged, the lamp shall be destroyed

1/2

PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY

A mounting screw 2X G Screwed Ball 2X

B mounting plate 1X I socket ring 1X

C ground screw 1X J Glass 1X

D Machine Screw 2X K bulb 1X

E wire connector 3X

Part List and Hardware List

1/2

Need help?

Do you have a question about the JONATHAN Y Jayne JYL7545A and is the answer not in the manual?

Summary

Preparation

Grounding Instructions

Guidance on correctly connecting the ground wire for safe installation in the US and Canada.

Summary

Preparation

Grounding Instructions

Guidance on correctly connecting the ground wire for safe installation in the US and Canada.

This document provides instructions for the installation, use, and maintenance of a lighting fixture, model JYL7545A, from JONATHAN Y. The fixture is designed for general illumination and is intended for indoor use.

Function Description

The JYL7545A is a wall-mounted lighting fixture that provides ambient light. It consists of a back plate that attaches to an electrical outlet box, a socket for a light bulb, and a glass shade that diffuses the light. The fixture is designed to be hardwired into a building's electrical system. It accommodates a single light bulb, with specific wattage recommendations to ensure safe and efficient operation. The assembly process involves securing the mounting plate to the outlet box, making electrical connections, attaching the fixture's back plate, securing the glass shade, and finally installing the light bulb.

Usage Features

The lighting fixture is designed for straightforward installation by a licensed electrician, as recommended by the manufacturer. Users should ensure all parts are present and undamaged before beginning assembly. The assembly process is estimated to take approximately 20 minutes.

Key steps for installation include:

Mounting Plate Installation: The mounting plate (B) is fixed to the electrical outlet box using machine screws (D). This plate serves as the foundation for the entire fixture.
Wire Connections: Electrical connections are made using wire connectors (E). The instructions provide a detailed chart for connecting hot (black or red) and neutral (white) outlet supply wires to the corresponding fixture wires. This chart covers various wire types, including parallel cords (round & smooth, square & ridged) and insulated wires with copper or silver metal conductors. Special attention is given to identifying neutral wires in parallel cords, which are typically square-shaped and ridged.
Grounding Instructions: Proper grounding is crucial for safety. For installations in the United States, the ground wire from the outlet box should be wrapped around the green ground screw (C) on the mounting plate, ensuring at least 2 inches of wire from the end. If the fixture itself has a ground wire, it should be connected to the outlet ground wire with a wire connector. For installations in Canada, if the fixture includes a ground wire, it should be wrapped around the green grounding screw on the mounting bracket.
Fixture Assembly: Once wiring is complete, the back plate (F) of the fixture is oriented so that the mounting screws (A) protruding from the mounting plate align with the holes in the back plate. These are then secured with screwed balls (G).
Shade and Bulb Installation: The glass shade (J) is placed onto the socket (H) and fastened securely with a socket ring (I). Finally, the light bulb (K) is installed. It is critical to use a light bulb with wattage no greater than specified for the fixture to prevent overheating and potential damage. The manual specifies using an ON/OFF Type "A" bulb with a maximum of 40 watts, a CFL bulb with a maximum of 13 watts, or an LED bulb with a maximum of 9 watts. The product typically includes one 4-watt LED bulb.

Safety Precautions:

Always switch off the main electrical supply from the fuse box/circuit breaker before installation or maintenance to prevent electrical shock.
Inspect the item carefully for any damage or obvious defects before installation. Do not install a damaged item; it should not be returned once installed.
Assemble the product on a soft surface to prevent scratching the finish.
Follow all guidelines for safe use and installation to reduce the risk of fire, electrical shock, or injury.
The external flexible cable or cord of this lamp cannot be replaced. If the cord is damaged, the lamp must be destroyed.
Always ensure electrical current is turned off before changing bulbs.

Maintenance Features

Maintaining the JYL7545A lighting fixture is straightforward and focuses on keeping the surfaces clean and ensuring safe operation.

Cleaning:

Exterior Cleaning: To clean the outside of the fixture, use a dry or slightly dampened clean cloth. It is important to use clean water and avoid any solvents, as these can damage the finish.
Interior Cleaning: For cleaning the inside of the fixture, first disconnect power by turning off the circuit breaker or removing the fuse at the fuse box. Then, use a dry or slightly dampened clean cloth (again, with clean water and no solvents) to wipe the interior surface.
General Cleaning: Avoid using any cleaners that contain chemicals, solvents, or harsh abrasives. For dusting or light wiping, a dry, soft cloth is recommended.

Bulb Replacement:

When replacing the light bulb, always ensure the electrical current is turned off at the main fuse box or circuit breaker.
Use only light bulbs that comply with the specified wattage limits (max 40-watt for Type "A", max 13-watt for CFL, max 9-watt for LED) to ensure the fixture operates safely and efficiently.

By following these instructions, users can ensure the safe and long-lasting operation of their JONATHAN Y JYL7545A lighting fixture.

JONATHAN Y Jayne JYL7545A Specifications

General

Brand	JONATHAN Y
Model	Jayne JYL7545A
Category	Home Lighting
Product Type	Table Lamp
Base Material	Metal
Shade Material	Linen
Shade Color	White
Bulb Type	LED
Bulb Included	Yes
Style	Contemporary
Material	Metal, Linen
Number of Lights	1
Voltage	120V
Wattage	9W
Height	26 inches
Weight	5.5 lbs
Base Color	Gold
Width	14 inches
Length	14 inches