Jonsered LT2113 CM - Page 16

15
TRACTOR - - MODEL NO. LT2113CM (96061022405), PRODUCT NO. 960 61 02-24
MOWER DECK
44
44
KEY PART
NO. NO. DESCRIPTION
1 532 42 91-21 Housing Asm. Mower
3 532 43 18-64 Bracket Asm. S-Bar Chass
5 532 12 46-70 Retainer Spring
6 532 16 55-57 Bar Sway
8 532 18 17-12 Bolt 3/8-24 x 1.25 Gr. 8 Patched
9 810 03 06-00 Washer Lock Hvy 3/8 Unplated
10 532 14 02-96 Washer Hard Blade Mower Vented
11 532 42 79-84 Blade 3-1 LH
13 532 13 76-45 Shaft Asm. w/Lower Bearing
14 532 12 87-74 Housing Mandrel Vented (Machd)
15 532 11 04-85 Bearing Ball Mandrel
16 532 42 79-85 Blade 3-1 RH
17 872 14 06-10 Bolt Carriage 3/8-16 x 1-1/4
19 532 13 28-27 Bolt Shoulder 5/16-18 Thd Form
20 532 18 17-13 Bolt 3/8-24 x 1.25 Gr. 8 Ptch Lhthd
22 532 43 11-69 Bracket Idler Sprt Rear RH
27 532 42 79-81 Bracket Asm. Susp. Rear RH
30 532 17 39-84 Screw Thd Rolling
31 532 18 76-90 Washer Spacer Mower Vented
32 532 15 35-32 Mandrel Pulleys
33 532 40 02-34 Nut Flg Top Lock
36 532 14 67-63 Pulley Idler V-Groove Dim 4.25
40 873 68 06-00 Nut Crownlock 3/8-16 unc
41 873 90 06-00 Nut Lock Flg. 3/8-16 unc
44 532 43 49-46 Cover Mandrel LH
45 532 44 14-79 Cover Mandrel RH
55 532 19 94-98 Arm Idler
56 532 16 57-23 Spacer Retainer Mower
61 532 19 94-86 Spring Tension Belt
67 532 10 69-32 Knob Rd 3/8-16
68 532 42 95-32 Drive Belt
69 532 16 54-82 Shaft Asm w/Lwr Brg RH Thd
84 532 15 60-85 Keeper Belt Idler
116 532 19 34-06 Bolt Shoulder
117 532 17 48-73 Wheel Gauge
119 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.
124 872 11 06-12 Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5
131 532 16 56-61 Chute Bagger
152 532 17 60-74 Cable Clutch CRD
158 817 72 04-08 Screw Hex Thd Cut 1/4-20 x 1/2
185 532 18 82-34 Head Asm Cable Clutch
260 817 67 06-08 Screw 3/8-16 x 1/2
298 817 49 06-28 Screw 3/8-16 x 1-3/4
-- 532 18 18-57 Mandrel Assembly (Includes hous-
ing, shaft assembly, and bearing
only - pulley/nut/washer and blade
bolt/washers not included)
-- 532 18 18-58 Mandrel Asm CRD LH Threads
SVC
-- 532 43 15-80 Replacement Mower, Complete
(Std. Deck - Order separately
gauge wheel components key
nos. 116-119)
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
KEY PART
NO. NO. DESCRIPTION