joule Cyclone - Thermostat Knob Setting Positions

www.jouleuk.co.uk | www.joule.ie
28
Knob setting position
the thermostat will lose all recorded
NOTE: Changing thermostat seng
set posion may impact upon the eciency rang of the cylinder in which it is ed.
knob turned on this
the thermostat will control water temperature to maximum 60°C and is
power supply. Use this posion for manual
ibacterial mode will funcon.
In this mode the thermostat will not operate, only the double pole safety cut
This seng will main
tain a minimum water temperature of
Anbacterial mode will funcon.
With the control knob turned
clockwise to the MAX seng the thermostat will control water temperature to a
. The water temperature can be adjusted to a lower seng by
turning the adjustment knob anclockwise up to 80° where the lowest seng is
This unit should be connected by a suitably qualied electrician in accordance with the latest I
.E.E.
before making any connecon to the unit.
The immersion heater must be wired through a double pole isolang switch with contact separaon
The immersion heater must be wired with a heat resistant exible cord with a minimum T rang of
Ensure that the terminal screws are not over ghtened as this could result in the terminaons being
the earth post (marked “E”) using the
brown) from the mains supply cab
le to the thermostat terminal marked “L”
(blue) from the mains supply cable to the thermostat terminal marked “N”
the thermostat will lose all recorded
NOTE: Changing thermostat seng
set posion may impact upon the eciency rang of the cylinder in which it is ed.
knob turned on this
the thermostat will control water temperature to maximum 60°C and is
power supply. Use this posion for manual
ibacterial mode will funcon.
In this mode the thermostat will not operate, only the double pole safety cut
This seng will main
tain a minimum water temperature of
Anbacterial mode will funcon.
With the control knob turned
clockwise to the MAX seng the thermostat will control water temperature to a
. The water temperature can be adjusted to a lower seng by
turning the adjustment knob anclockwise up to 80° where the lowest seng is
This unit should be connected by a suitably qualied electrician in accordance with the latest I
.E.E.
before making any connecon to the unit.
The immersion heater must be wired through a double pole isolang switch with contact separaon
The immersion heater must be wired with a heat resistant exible cord with a minimum T rang of
Ensure that the terminal screws are not over ghtened as this could result in the terminaons being
the earth post (marked “E”) using the
brown) from the mains supply cab
le to the thermostat terminal marked “L”
(blue) from the mains supply cable to the thermostat terminal marked “N”
the thermostat will lose all recorded
NOTE: Changing thermostat seng
set posion may impact upon the eciency rang of the cylinder in which it is ed.
knob turned on this
the thermostat will control water temperature to maximum 60°C and is
power supply. Use this posion for manual
ibacterial mode will funcon.
In this mode the thermostat will not operate, only the double pole safety cut
This seng will main
tain a minimum water temperature of
Anbacterial mode will funcon.
With the control knob turned
clockwise to the MAX seng the thermostat will control water temperature to a
. The water temperature can be adjusted to a lower seng by
turning the adjustment knob anclockwise up to 80° where the lowest seng is
This unit should be connected by a suitably qualied electrician in accordance with the latest I
.E.E.
before making any connecon to the unit.
The immersion heater must be wired through a double pole isolang switch with contact separaon
The immersion heater must be wired with a heat resistant exible cord with a minimum T rang of
Ensure that the terminal screws are not over ghtened as this could result in the terminaons being
the earth post (marked “E”) using the
the thermostat will lose all recorded
NOTE: Changing thermostat seng
set posion may impact upon the eciency rang of the cylinder in which it is ed.
knob turned on this
the thermostat will control water temperature to maximum 60°C and is
power supply. Use this posion for manual
ibacterial mode will funcon.
In this mode the thermostat will not operate, only the double pole safety cut
This seng will mai
ntain a minimum water temperature of
Anbacterial mode will funcon.
With the control knob turned
clockwise to the MAX seng the thermostat will control water temperature to a
. The water temperature can be adjusted to a lower seng by
turning the adjustment knob anclockwise up to 80° where the lowest seng is
This unit should be connected by a suitably qualied electrician in accordance with the latest
I.E.E.
before making any connecon to the unit.
The immersion heater must be wired through a double pole isolang switch with contact separaon
The immersion heater must be wired with a heat resistant exible cord with a minimum T rang of
Ensure that the terminal screws are not over ghtened as this could result in the terminaons being
ECO – Smart mode F actory Setting – This setting gives maximum energy ef -
-
In the event of any power loss the thermostat will lose all recorded data, and
will restart learning mode. Antibacterial m
ode will function.
OPK
on this position the thermostat will control water temperature to maximum
-
tion for manual switching or by timer such as economy type installations.
Antibacterial mode will function.
OFF – In this mode the thermostat will not operate, only the double pole
the most ecient use of electricity. In the event of any power loss the thermostat will lose all recorded
data, and will restart learning mode. Anbacterial mode will funcon. NOTE: Changing thermostat seng
from the factory pre-set posion may impact upon the eciency rang of the cylinder in which it is ed.
OPK – Basic Electronic Thermostat mode – With the control knob turned on this
posion the thermo
stat will control water temperature to maximum 60°C and is
unaected by any interrupon of power supply. Use this posion for manual
switching or by mer such as economy type installaons. Antibacterial mode will funcon.
OFF – In this mode the thermostat will not operate, only the double pole safety cut
out will funcon. Anbacterial mode will NOT funcon.
-
Anfreeze mode – This seng will maintain a minimum water temperature of
20°C to prevent the water heater from freezing. Anbacterial mode will funcon.
MAX – Maximum temperature in Manual Mode – With the control knob turned
clockwise to the MAX seng the thermostat will control water temperature to a
maximum of 70°C. The water temperature can be adjusted to a lower seng by
turning the adjustment knob a
nclockwise up to 80° where the lowest seng is
approximately 10°C. Anbacterial mode will funcon
ELECTRICAL CONNECTIONS
1. This unit should be connected by a suitably qualied electrician in accordance with the latest I.E.E.
regulaons.
2. Ensure the electrical supply is switched o before making any connecon to the unit.
3. The immersion heater must be wired through a double pole isolang switch with con
tact separaon
of at least 3mm in both poles.
4. The immersion heater must be wired with a heat resistant exible cord with a minimum T rang of
“T-80” and with a minimum cross-secon area of 1.5mm
2
.
5. Ensure that the terminal screws are not over ghtened as this could result in the terminaons being
broken o.
WARNING: THIS DEVICE MUST BE EARTHED
WIRING:
1. Earth connecon (green & yellow) should be made
rmly to the earth post (marked “E”) using the
terminals aachments provided.
Antifreeze mode – This setting will maintain a minimum water temper -
will function.
MAX – Maximum temperature in Manual Mode – With the control knob
-
thermostat.
replacement must be of the same type.
ded to reduce limestone deposit (Not lower
both supply conductors (live and neutral) by a single
out mechanism which prevents excessive temperatures. In
device will act to limit the water
hermostat.
if this is found to be operang frequently then we recommend to consult
as the thermostat may need to be replaced.
It may be helpful to lower the thermostat sen
g to avoid unnecessary cut o.
hermostat has 5 operang modes, and is supplied set to the
maximum control temperature of 70°C. To select the alternave modes the adjustment knob is turned
with the required mode:
This seng gives maximum energy eciency
habits to control water temperature
70°C whilst
recording hot water usage, then the following and each subsequent week it adjusts automacally to give