MO-6900S Series (September, 2003) 4/4
DEVISES AND ATTACHMENTS
● Chain-off thread trimming device
● Blower-type chain-off thread suction device
● Pneumatic chain-off thread suction device
● Auto-lifter
● Gathering device
● Blind hemming device
● Piping folder
● Guide, Ruler
● Feller, Binder
Model Part No. Description
T039
MAT-039001A0 For 110, 115, 220, 240V
MAT-039002A0 For 220, 380, 415, 440V
MAT-040001A0 For 110, 115, 220, 240V
T040
MAT-040002A0 For 220, 380, 415, 440V
MAT-040001AA For 110, 115, 220, 240V
MAT-040002AA For 220, 380, 415, 440V
T041 MAT-041000A0A Pneumatic flat cutter
T042 MAT-042000A0 Pneumatic side cutter (for overlock machine)
MC-4 ― Specific to chain-off thread, pedal-operated
MC-5 ― Specific to chain-off thread
MC-8 ― Pneumatic chain-off thread + cloth chips
MC-9 ― Function of MC-8 + auto-lifter
MC-24 ― Pneumatic chain-off thread + cloth chips
AK32 GAK-320000A0 Pneumatic type (knee-operated)
AK49 GAK-490000A0 Pneumatic type (pedal-operated)
AK101 GAK-A01000A0 Pneumatic type (for servomotor)
S159 MAS-159000A0
Swing-type gathering device
(interlocked with pedal / for safety stitch machine)
S160 MAS-160000A0
Swing-type gathering device
(interlocked with pedal / for overlock machine)
S161 MAS-161000A0
Swing-type gathering device
(manual-lever operated / for safety stitch machine)
S162 MAS-162000A0
Swing-type gathering device
(manual-lever operated / for overlock machine)
― PF-0552010-B0 Air regulator (F.R. unit asm.)
― GMD-01080000×2Fixing screw for F.R. unit asm.
― F1021-003-000 Tube connector (male)
― GAS-12063000
＊
One-touch connector
＊Selection parts instead of the tube connector
MC-7A ―
Blower-type chain-off thread suction device + cloth chips
One-touch type tape cutter
and chain-off thread
trimming device
(electromagnetic type)
Automatic tape cutter
+ chain-off thread
trimming device
(number-off-stitch
control and electro-
magnetic type)
[Reference]
Combination table of “chain-off thread suction device” and
“auto-lifer” which correspond to “chain-off thread trimming device”.
Chain-off
thread
trimming
device
T039
T040
T041
or
T042
Chain-off
thread
suction
device
Auto-lifter
MC-7A AK101 (JUKI servomotor)
MC-8 AK101 (JUKI servomotor)
MC-9 ― (MC-9 is equipped with auto-lifter.)
MC-7A AK32 (any motor will do)
MC-5 AK32 (any motor will do)
MC-24 AK32 (any motor will do)
AK49
(Motors other than JUKI servomotors
are applicable.)
MC-7A
AK101 (JUKI servomotor)
MC-4 ―
MC-8 AK101 (JUKI servomotor)
MC-9 ― (MC-9 is equipped with auto-lifter.)
For semi-
sunken type
For fully-
sunken type
L121 MAL-121000A0 Blind stitch hemming attachment A ruler used for blind hemming in knits
M056 MAM-0560J0A0 Piping folder This piping folder makes a piping first, then turns up the tape.
M075 MAM-0750J0A0 Piping folder (to be used with knit tape)
This attachment can be used for both “cotton bias tape with gimp” and “knit tape”.
The operation mode can be changed over with a fingertip control.
M076 MAM-0760N0A0 Ready-made piping folder
The dimension of ready-made tapes can be adjusted within the range of 8 to 13mm.
M077 MAM-0770M0A0 Piping folder for gathering
The attachment makes gathers on the lower fabric while making decorative piping.
H153 MAH-153000A0 Cloth edge guide ruler (for overlock machine)
A swing type edge guide.
H154 MAH-154000A0 Cloth edge guide ruler (for safety stitch machine)
Q141 MAQ-141000B0 Tape guide
K006 MAK-00601000
Upturn feller
This feller is exclusively used with the 3C0 throat plate. It is attached on the throat plate.
N067 MAN-0670D0A0
Reinforcement tape attachment binder (finished width: 4mm)
This binder binds the edge of a pocket bag while cutting round its periphery.
＊The aforementioned devices are not equipped with air regulator.
Please purchase the following components when you need to regulate air pressure.
Model Part No. Description Feature
The attachment opens with the presser foot pedal. This facilitates material
setting on the machine. Furthermore, knee-control type differential-feed
adjusting device is built in the attachment. It controls a differential-feed ratio
as desired, thereby enabling the operator to make beautiful gathers.
The attachment is used to perform two different processes, joining fabric
process and gathering process, at a time.
The attachment can be opened/closed by using the lever (manually operated).
The differential-feed ratio is controlled with the knee lever.
This attachment is used attached on the machine head (face plate).
It is used for tapes with the width of 7mm or less.
To Next Page
Loading...
Need help?
General
