MO-6900R Series (September, 2003) 3/3
DEVISES AND ATTACHMENTS
● Chain-off thread trimming device
Model Part No. Description
T039
MAT-039003A0 For 110, 115, 220, 240V
MAT-039004A0 For 220, 380, 415, 440V
MAT-040005A0 For 110, 115, 220, 240V
T040
MAT-040006A0 For 220, 380, 415, 440V
MAT-040005AA For 110, 115, 220, 240V
MAT-040006AA For 220, 380, 415, 440V
T041 MAT-041000AB Pneumatic flat cutter
T045 MAT-045000A0 Pneumatic side cutter (for overlock machine)
● Pneumatic chain-off thread suction device
MC-4 ― Specific to chain-off thread, pedal-operated
MC-5 ― Specific to chain-off thread
MC-8 ― Pneumatic chain-off thread + cloth chips
MC-9 ― Function of MC-8 + auto-lifter
MC-24 ― Pneumatic chain-off thread + cloth chips
● Auto-lifter
AK32 GAK-320000A0 Pneumatic type (knee-operated)
AK49 GAK-490000A0 Pneumatic type (pedal-operated)
AK101 GAK-A01000A0 Pneumatic type (for servomotor)
● Gathering device
S167 MAS-167000A0
Swing-type upper-cloth gathering device
(interlocked with pedal)
― PF-0552010-B0 Air regulator (F.R. unit asm.)
― GMD-01080000×2Fixing screw for F.R. unit asm.
― F1021-003-000 Tube connector (male)
― GAS-12063000
＊
One-touch connector
＊Selection parts instead of the tube connector
MC-7A ― Blower-type chain-off thread suction device + cloth chips
● Blower-type chain-off thread suction device
One-touch type tape cutter
and chain-off thread
trimming device
(electromagnetic type)
Automatic tape cutter
+ chain-off thread
trimming device
(number-off-stitch
control and electro-
magnetic type)
[Reference]
Combination table of “chain-off thread suction device” and
“auto-lifer” which correspond to “chain-off thread trimming device”.
Chain-off
thread
trimming
device
T039
T040
T041
or
T045
Chain-off
thread
suction
device
Auto-lifter
MC-7A AK101
(JUKI servomotor)
MC-8 AK101
(JUKI servomotor)
MC-9 ― (MC-9 is equipped with auto-lifter.)
MC-7A AK32 (any motor will do)
MC-5 AK32 (any motor will do)
MC-24 AK32 (any motor will do)
MC-7A AK101
(JUKI servomotor)
MC-8 AK101
(JUKI servomotor)
MC-9 ― (MC-9 is equipped with auto-lifter.)
For semi-
sunken type
For fully-
sunken type
● Blind hemming device
L121 MAL-121000A0 Blind stitch hemming attachment A ruler used for blind hemming in knits
● Piping folder
M056 MAM-0560J0A0 Piping folder This piping folder makes a piping first, then turns up the tape.
M075 MAM-0750J0A0 Piping folder (to be used with knit tape)
This attachment can be used for both “cotton bias tape with gimp” and “knit tape”.
The operation mode can be changed over with a fingertip control.
M076 MAM-0760N0A0 Ready-made piping folder
The dimension of ready-made tapes can be adjusted within the range of 8 to 13mm.
M077 MAM-0770M0A0 Piping folder for gathering
The attachment makes gathers on the lower fabric while making decorative piping.
M222
MAM-2220M0A0
Piping folder upper-cloth gathering
(finished width 12mm, tape width 26mm)
MAM-2220J0A0
Piping folder upper-cloth gathering
(finished width 9mm, tape width 20mm)
M224 MAM-2240N0A0 Ready-made piping folder for upper-cloth gathering
● Guide, Ruler
H153 MAH-153000A0 Cloth edge guide ruler (for overlock machine)
A swing type edge guide.
H154 MAH-154000A0 Cloth edge guide ruler (for safety stitch machine)
Q141 MAQ-141000B0 Tape guide
＊The aforementioned devices are not equipped with air regulator.
Please purchase the following components when you need to regulate air pressure.
Model Part No. Description Feature
The attachment opens with the presser foot pedal. This facilitates material
setting on the machine. Furthermore, knee-control type differential-feed
adjusting device is built in the attachment. It controls a differential-feed ratio
as desired, thereby enabling the operator to make beautiful gathers.
This attachment is used attached on the machine head (face plate).
It is used for tapes with the width of 7mm or less.
This folder is to be used together with upper-cloth gathering device S167.
Gimp size that can be used is φ2 to φ2.5mm.
This folder is to be used together with upper-cloth gathering device S167.
Tape, of which width is 8 to 18mm, can be used.
To Next Page
Loading...
Need help?
General
