Need help?Do you have a question about the Julabo SE-6 and is the answer not in the manual?
General| Brand | Julabo |
|---|---|
| Model | SE-6 |
| Category | Water System |
| Language | English |
Overview of the circulator's features and capabilities.
Guidelines for safe operation and handling of the circulator.
Instructions for proper disposal of the circulator and its components.
Detailed technical data for heating circulators and bridge mounted circulators.
Interpretation of safety warnings, danger classifications, and informational notes.
Specific guidelines to avoid personal injury and property damage during operation.
Description of controls and displays on the front panel of the unit.
Identification of connectors and ports on the rear panel.
Functionality of navigation keys, menu keys, header indicators, and pump display.
Details on Pt100, RS232, Control/Alarm sockets, and Optional Electronic Module.
Instructions for installing heating circulators and bridge mounted circulators.
Selection criteria, recommendations, and warnings for bath fluids.
Connecting the circulator for temperature control of external systems.
Guidelines for selecting and connecting tubing for external systems.
Procedures for filling, draining the bath fluid, and connecting countercooling.
Instructions for safely connecting power and starting the circulator.
Adjusting and using stored temperature setpoints via the T menu.
Changing the target temperature directly using the keypad.
Configuration and function of excess temperature protection and low level warnings.
Setting the response from warning signals to automatic shutdown.
Setting upper and lower temperature warning limits for sensitive applications.
Starting, creating, editing, and deleting temperature programs.
Detailed steps for creating, editing, and deleting programs with sections.
Procedures for modifying existing programs or removing them.
Adjusting the circulator's pump capacity in four stages.
Settings for remote control, autostart, OFF-MODE, and system reset.
Adjusting the internal real-time clock and resetting unit parameters.
Configuring serial remote control and analog input setpoint adjustments.
Enabling automatic restart after power interruption or timer activation.
Configuring OFF-MODE operation and the actuating variable for control.
Setting internal/external control types and selftuning parameters.
Switching between internal and external temperature control modes.
Adjusting PID parameters (XP, TN, TV) for internal and external control.
Information on connecting and using the Pt100 external temperature sensor.
Configuring selftuning and dynamic parameters for internal control.
Detailed explanation of XP, TN, TV parameters for internal PID control.
Adjusting CoSpeed and PID parameters for external control processes.
Configuring baud rate, parity, and handshake for serial communication.
Methods and process for performing absolute temperature calibration.
Illustrates 1-point and 3-point calibration methods for precise temperature control.
Choosing between internal/external sensors and activating/deactivating calibration.
Detailed configuration for ATC sensor selection and status activation.
Choosing between 1, 2, or 3-point calibration methods.
Step-by-step guide for performing a 3-point calibration for internal control.
Setting maximum/minimum temperature, heating/cooling limits.
Defining setpoint limits and maximum heating/cooling for internal control.
Setting internal bath limits and safety limits for external control.
Limiting temperature differences between internal and external systems.
Setting analog input/output values for recorder and programmer.
Configuring voltage and current outputs for specific analog channels.
Setting E-PROG values and configuring stand-by/alarm inputs/outputs.
Defining output values for channels 1, 2, and 3 on the REG+E-PROG connector.
Connecting external sources and defining input variables for the E-PROG connector.
Step-by-step guide to setting low and high values for E-PROG input.
Configuring alarm signals and external stand-by input functionality.
How to activate and use the external stand-by input for switch-off.
Error codes and descriptions for alarms causing a full shutdown.
Error codes and descriptions for alarms that do not cause a full shutdown.
Detailed list of error codes and their associated causes for diagnosis.
Pin assignment and connection details for the external Pt100 sensor.
Pin assignments and cable details for RS232 remote control.
Pin assignments for various output and input connectors.
Configuring the circulator and PC for remote control and data transfer.
Comprehensive list of OUT commands for setting parameters and values.
Commands for retrieving parameters and displaying values from the circulator.
More IN commands for retrieving status, parameters, and configuration settings.
Descriptions of the circulator's operational status messages.
List of error codes, their meanings, and initial troubleshooting steps.
Detailed list of error codes and their associated causes for diagnosis.
Details on warranty coverage, exclusions, assignment, governing law, waiver, and freight.
To Next Page
