Jura IMPRESSA X7 - Drawing off Hot Water; Drawing off Steam; Drawing-Off Milk Froth; Switching the Machine off

9
11. Drawing off hot water
 : SELECT PRODUCT
 Place a cup under the pivoting nozzle (18) and press the draw-
off key .
 : PORTION HOT WATER
 The draw-off of the programme portion of hot water stops auto-
matically.
You can interrupt the draw-off prematurely at any time by
pressing the draw-off key again.
When water is drawn off, there can be splattering at the
beginning. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
12. Drawing off steam
 : SELECT PRODUCT
 Place a cup with the liquid to be heated under the pivoting
nozzle (18) and press the draw-off key .
 : STEAM ACTIVE
 To end the draw-off of steam, press the key .
When steam is drawn off, there can be splattering at the
beginning. The pivoting nozzle becomes hot. Avoid direct
contact with the skin.
13. Drawing-off milk froth
 : SELECT PRODUCT
 Pour milk / Tetra Pak into a jug and immerse the cappuccino
tube into the milk.
 Place 1 cup under the coffee spout (4) and press the draw-off
key .
The programme amount is prepared and stops automatically.
You can interrupt the draw-off prematurely at any time by
pressing the draw-off key again.
10 min. after the draw-off of milk, a rinsing is automatically
started. The rinsing is announced in advance by an acoustic
signal.
14. Switching the machine off
 Switch the machine off with the ON/OFF operating switch. A
rinsing is automatically started when the machine is switched
off.
15. Programming
The following phases can be programmed:
 Grinding amount
 Temperature
 Amount of water
 Amount of milk
 Portion of hot water
 Water hardness
 Clock
 Machine on
 Machine off
 Draw-offs
 Language
15.1 Programming grinding amount
 Switch your machine on the with ON/OFF operating switch.
 Press the key PROG. until an acoustic signal is heard.
 : ADJUST COFFEE QUANTITY /
SELECT PRODUCT
 Press the required draw-off key.
 : (selected product)
–
..............
II
..............
+
 By pressing the key or you can determine the amount to
be ground.
 To store, press the key PROG.
 : (selected product)
: 100% : 0%
You can determine the allocation of the grinder “left” or “right”.
 By pressing the key or you can change the values.
 To store, press the key PROG.
 : ADJUST COFFEE QUANTITY /
SELECT PRODUCT
 Press the required draw-off key, the key in order to reach the
next phase or the key EXIT to quit the programming.
15.2 Programming Temperature
 : ADJUST TEMPERATURE / SELECT PRODUCT
 Press the required draw-off key.
 : (selected product)
STAND. TEMP.
 Select the required temperature with the keys or (high or
standart)
 To store, press the key PROG.
 : ADJUST TEMPERATURE / SELECT PRODUCT
 Press the required draw-off key, the key in order to reach the
next phase or the key EXIT to quit the programming.
15.3 Programming amount of water
 : ADJUST WATER QUANTITY /
SELECT PRODUCT
 Press the required draw-off key.
 : (selected product)
WATER 90 ML
 You can change the value by pressing the key or .
 To store, press the key PROG.
 : ADJUST WATER QUANTITY /
SELECT PRODUCT
 Press the required draw-off key, the key in order to reach the
next phase or the key EXIT to quit the programming.
15.4 Programming amount of milk
 : ADJUST MILK QUANTITY / SELECT
PRODUCT
 Press the key or
 : (selected product)
10 SEC.
 You can alter the time by pressing the keys or (draw-off
time from 3 – 60 sec.)
 To store, press the key PROG.
 : ADJUST MILK QUANTITY / SELECT
PRODUCT
 Press the required draw-off key, the key in order to reach the
next phase or the key EXIT to quit the programming.
+
-
+
+
-
+
+
-
+
+
-
+
-
+
E