ENGLISH - 14 -
Press button.
Select the required subcode page number by pressing four
digit buttons (e.g. 0001).
If the selected subcode page is not displayed in a short
time, press
button. TV programme will be displayed on
the screen.
Teletext page number will be displayed on the upper left cor-
ner of the screen when the selected page is found.
Press
button to display the selected Teletext page.
To exit Teletext
Press button. The screen will switch to TV mode.
Fastext and Toptext
Teletext mode will be selected according to transmission au-
tomatically.
Your CTV supports the 7 page Teletext system. When the
page number of any of the 7 pages in memory is entered, the
system will not search for the requested page; instead it will
display the page automatically.
Press
button to move the Teletext screen forward
one page at a time.
Press
button to move the Teletext screen backward
one page at a time.
For Fastext and Toptext:
The subject-heading for the information may have a particular
colour or can be in a form located in a coloured box.
Press an appropriate RED, GREEN, YELLOW or BLUE but-
ton in order to reach the relevant page quickly.
For TOPTEXT:
If Toptext transmission is present, colour coded buttons will
appear in status row.
If Toptext transmission is not present, status row will not ap-
pear.
In Toptext mode the
or commands will request
the next or previous page respectively. If Toptext transmission
is not available, in case of operation of these commands,
wraparound occurs. For example page 100 appears to be one
greater than page 199.
Connect the External Equipments
Via the Euroconnector
Your TV set has three Euroconnector sockets. If you want to
connect equipments (e.g. video recorder, decoder, etc.) which
have Euroconnectors, to your TV, use the EXT.1 (EXT-1),
EXT.2 (EXT-2) or EXT.3 (EXT-3) terminals.
T-V LINK compatible VCR
Be sure to connect the T-V LINK compatible VCR to the
EXT-2 terminal. If not, the T-V LINK function will not work
properly.
When connecting a T-V LINK compatible VCR to the EXT-2
terminal, be sure to connect the decoder to the VCR. If not,
the T-V LINK function may not work properly. And then set
the DECODER (EXT-2) function for the channel to ON to un-
scramble a scrambled channel. For details, see Using the
Decoder (EXT-2) function on page 10.
RGB mode
If an equipment can output the RGB signals, connect it to the
EXT-1 (EXT.1) terminal.
EXT-2 S Mode
If the equipment connected to your TV set supports S-Video
(Y/C) output from Euroconnector, you can have a better pic-
ture quality by selecting EXT-2 S mode and connecting your
equipment to the EXT.2 (EXT-2 S) terminal of TV. See your
equipment's booklet to check if your equipment has such fea-
ture.
Via the RCA jacks
If you have an equipment (such as a Camcorder) which has
the RCA jacks, connect it to the Front AV (EXT-4) terminal
with the video and audio cables.
If the epuipment has the mono audio jack, connect it to the
AUDIO-L jack.
Via the ANT (aerial) socket
If your equipment does not have a Euroconnecter or RCA
jacks, connect it to the TV with an aerial cable. For details,
see the manual provided with the equipment.
To store the test signal that comes from the equipment in a
programme number, follow the instructions of "Tuning
menu" on page 9. The programme number 0 is usually
used for the external equipment.
After storing, you can watch images from the equipment by
selecting the programme number which you stored the test
signal.
TV and Video Recoder (VCR)
Connect the Video Recorder to the ANT (antenna input)
socket of the TV with the aerial cable.
Connect the Video Recorder to the EXT.1, EXT.2 or EXT.3
terminal with the SCART cable, or connect it to the Front
AV (EXT-4) terminal with the audio and video cables.
When you watch a picture from your VCR and the picture is
unstable, you may improve it by changing the Mode set-
ting in the TUNING menu. (See the Tuning Menu on
page 9.)
NTSC Playback
Connect a NTSC video recorder to a terminal. Then press
AV button to select the corresponding AV mode.
NTSC 3.58/4.43 system is detected automatically in AV
mode.
Copy Facility
You can output the video and audio signals which inputs from
TV, EXT.1 (EXT-1), EXT.3 (EXT-3), Front AV (EXT-4) terminal
to the video recorder connected to the EXT.2 (EXT-2) termi-
nal.
To select the output source, see Setting External Source
Output on page 12.
Connecting Headphones
Use the stereo headphone socket of your TV, to connect
headphones. As soon as you connect your headphone to the
headphone socket, TVs loudspeakers will automatically
mute.
01-ENG-2835-AK52-1512UK-16-9-(AV-28GH1&BUF&SUF).p65 21.05.2003, 15:0214
To Next Page
Loading...
