(No.PA056<Rev.002>) 3
Design and specifications are subject to change without notice.
INPUT CONNECTORS
HDMI
2-System (screw lock mechanism) / Equivalent to
HDMI2.0b
HDCP2.2 / 4K signals / 3D signals (FP, SBS, TAB) /
Deep Color: 8/10/12bit / Color space: YCbCr (4:4:4),
YCbCr (4:2:2), RGB / Input level: 0-255 (PC), 16-235
(Video), 16-255 (Super White)
For details of supported signals, refer to the WEB in-
struction manual.
To view all supported signals of this unit, we recom-
mend cables that support a transfer speed of
18Gbps.
EDID can be switched at the user menu only for the
HDMI 2 terminal.
EDID setting value A: Factory default (HDMI2.0b) /
B:4K input not allowed (DLA-X95R, X75R, X55R,
X35 equivalent)
Not used
Display
Port
terminals Not used
4 lines / Display Port, 1 input mode (Display Port 1 to
4 can be selected)
2 input mode (using Dipaly Port 1 and 3, 2 stripes,
frame sequential)
4 input mode (using Dipaly Port 1 to 4, cross, 4
stripes, frame sequential)
Input level - INPUT MODE: 0-255 (PC) /16-235 (Video)
Color space - YCbCr (4:4:4), YCbCr (4:2:2), RGB
version - Equivalent to Ver.1.2
HDCP version - incompatible
Input (Max) - 4096 x 2160 @ 120Hz
Deep Color - 8/10/12bit
CONTROLL CONNECTORS
Trigger
1 line /
Ø3.5 mm DC Power jack ( ) / 12 V /
maximum 0.1 A
Not used
Output timing: off / on (Power) / on (Anamo)
IR Remote
IR remote control, Distance: 7m, Angle range: Horizontal ±30 degrees, Vertical ±20 degrees
One remote control sensor each in front and behind the unit
Remote control A/B (Factory default: "A", To switch settings: Choose user menu on the unit, press "MENU"
and "BACK" on the remote control at the same time)
ECO Mode
OFF(Factory default value) :DLA-RS4500K
ON (Factory default value) : Except DLA-RS4500K
Not used
LAN terminal
1 line / RJ-45 plug
10BASE-T/100BASE-TX
Supports DHCP / Control 4 SDDP (ON / OFF possible)
PJ control / service correspondence / calibration
compatible
1 line / RJ-45 plug
10BASE-T/100BASE-TX
Supports DHCP / PJ control / service correspon-
dence / calibration compatible / for firmware up
RS-232 terminal
1-System/RS-232C/D-Sub9 pin, JVC External command system (HD-ILA compliant), all settings status,
individual retrieval possible, maintains OSD display when reference commands are received during OSD
display, (except SSSV)
Syncro terminal Not used 1 line /
Ø3.5 mm stereo mini ( ) / 5V, TTL output
3D SYNCRO terminal
1 line / Mini DIN 3 Pin
Emitter PK-EM 2 (wireless system) / PK-EM 1 (Infra-
red system: Discontinued product)
Not used
SERVICE terminal (USB) 1 line / USB Type A / for firmware up
Wired remote
Not used
1 line /
Ø3.5 mm stereo mini ( ) / Power sup-
ply 5V, maximum 3mA output / signal 5V, TTL input
Corresponding signal
Refer to the WEB instruction manual.
Item
DLA-RS4500K
DLA-Z1E
DLA-Z1C
DLA-VS4500
To Next Page
Loading...
