Masterpage:Right+
EN 43
Filename [DR-MV1SE_06DVD Operation2.fm]
Page 43 April 9, 2004 11:33 am
OPERATIONS ON DVD DECK
You can programme this unit to timer-record as many as
8 programmes.
With the S
HOWVIEW system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognise.
You can use the remote control to enter the S
HOWVIEW number.
1 Load a recordable disc.
2 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3 Press SHOWVIEW to access the SHOWVIEW screen.
4 Press the number keys to
enter the S
HOWVIEW number of a
programme you wish to record,
then press ENTER.
● If you have made a mistake, press
CANCEL (&) and input the correct
number before you press ENTER.
● To clear all entered numbers at a
time, press CLEAR(8).
● If the number you entered is invalid, “SHOWVIEW NO. ERROR
CONFIRM SHOWVIEW NO. THEN RETRY” appears on the TV
screen. Input a valid S
HOWVIEW number.
● If “GUIDE PROGRAMME IS NOT SET SELECT CHANNEL YOU
WANT TO RECORD” appears on the TV screen, set Guide Program
numbers manually. (墌 pg. 82)
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMME” appears on the TV screen, you need to cancel some
of the reserved programmes. (墌 pg. 47)
5 The SHOWVIEW number you entered and the matching timer-
recording information are displayed on the TV screen. Check the
programme data.
● To cancel this setting, press SHOWVIEW or RETURN.
6 Press we to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “STOP” (To advance/go back the stop time by 30 minutes, press and
hold rt).
● “DAILY/WEEKLY” (墌 pg. 43, “Daily/Weekly Recording”)
● “REC MODE” (墌 pg. 40, “Recording Mode”)
● “NAME” (墌 pg. 59, “Modify Programme Name”)
● “VPS/PDC” (墌 pg. 44, “VPS/PDC Recording”)
7 Press ENTER to access the Programme Confirmation screen.
8 Press ENTER to complete timer programming.
● To programme another timer, repeat steps 3 – 8.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 47.
9 Press DVD TIMER (#) to engage the unit’s timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. Press 1 to turn off the unit. When the
VCR deck is in timer standby mode, the unit is automatically turned
off.
● To disengage the timer mode, press DVD TIMER (#) again.
NOTES:
● There may be cases that SHOWVIEW Timer Programming function
prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with SHOWVIEW Timer Programming function, the beginning of the
second one may be left off the recording.
● SHOWVIEW Timer Programming is not possible on the discs used
exclusively for On-Disc Timer Programming.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
Daily/Weekly Recording
You can record programmes with one of the following weekly/daily
timer settings.
WEEKLY: Select to record a weekly programme.
MON–FRI: Select to record a daily programme from Monday
through Friday.
MON–SAT: Select to record a daily programme from Monday
through Saturday.
SUN–SAT: Select to record a daily programme from Sunday
through Saturday.
SHOWVIEW
TM
Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “SHOWVIEW
TM
System Setup” (墌 pg. 82) and set
the Guide Program number correctly.
1
4
7
2
5
8
0
3
6
9
0 – 9
RETURN
ENTER
SHOWVIEW
CLEAR (8)
CANCEL (X)
DVD TIMER (#)
VCR/DVD
SAT
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
programme number has been changed, the wrong programme
number will be displayed on the SHOWVIEW programme screen in
step 5. When this happens, set the correct Guide Program number
for that station. (墌 pg. 82, “SHOWVIEW
TM
System Setup”)
Satellite Receiver Users
To timer-record a satellite broadcast using the S
HOWVIEW
system:
A Perform “Satellite Receiver Control Setting (DVD Deck Only)”
(墌 pg. 21).
B Perform “S
HOWVIEW
TM
Timer Programming” (墌 pg. 43).
C Leave the satellite receiver’s power on.
DR-MV1SE_00.book Page 43 Friday, April 9, 2004 3:15 PM
To Next Page
Loading...
Need help?
General
