JVC RC-QC7 - Page 12

(9€00 LON) 24
@ CONTINUE appears in the display window and continuous play starts.
Playback is repeated from DISC 1 through DISC 3.
® Ifa tray does not contain a CD, playback will skip to the next tray.
© To end continuous play
Press the CONTINUE button and release it. The CONTINUE display
disappears and norma! play resumes.
e When closing the subtrays
De not foad the DISC 1 subtray by hand, as the CD may not be placed
onto the CD tray correctly. If a 12 cm CD is loaded this way, the CD
tray will not close. If an 8 cm CD is inserted incorrectly, the tray will
close, then eject the CD immediately. Afterwards, the CD mode will
not function. Remove the CD and tum the 5/loff and on again to
engage the CD mode.
Note:
@ When loading or ejecting a CD, do not hit the recorded surface of the
CD against the comer of the CD tray, as this may damage it.
DISC CONTROL button
@ Direct Disc Selection
Press the CD CONTROL button (DISC 1 to DISC 3) corresponding to
the No. of the required CD.
Example: To designate Disc 2
The tracks on the designated CD are played in sequence.
Note:
@ When “PROGRAM” is shown in the display and the direct select
operation is performed, the CD cannot be played.
Direct access play (using the remote control unit)
Example 1: To designate Disc 1
@ Designate the required CD using CD CONTROL button (DISC 1 to
DISC 3).
® CD play starts.
Example 2: To designate the 3rd track of Disc 3
@ Designate the required CD using the CD CONTROL buttons (DISC 1
to DISC 3).
@ The track number is displayed and the required track number is
selected using the track button.
© CD play starts.
© To designate track numbers 1 to 10, press the track number button
corresponding to the track number.
© To designate track number 11 or higher, press the +10 button the
required number of times, then a track number button. (Example: To
designate the 20th track, press the +10 button once, then press track
number button 10.)
* +10 button:
Each time this button is pressed, the number increases by 10. First
press this button to set the 10's digit, then press the track number button
to set the 1's digit.
14
Repeat play (Using the remote control unit.)
Press the REPEAT button before or during play. It is possible to perform
repeat play of a single track, all tracks on one CD, or all tracks on ail
CDs in the CD changer.
Each time the REPEAT button is pressed, the mode will change in the
order from a single track (C=), to all tracks (= ALL), to clear mode.
REPEAT
SS
D
SALL
>
oooson
Single track All tracks Repeat playback is released.
) ee eee ee eee |
®@ Single track repeat (—)
The current or specified track will be played repeatedly.
@ Ail tracks of one CD repeat (@ ALL)
All tracks on the current or specified CD will be played repeatedly.
© All tracks of all CDs repeat (ALL DISC. CONTINUE. @ ALL)
When the CONTINUE button is pressed in the “c= ALL” mode, CD
play starts from the current or specified track, then all tracks on all CDs
will be played repeatedly.
Random piay (using the remote control unit)
Press the RANDOM button before or during play. It is possible to perform
random play from one or all CDs.
@ One disc random (RANDOM)
Press the RANDOM button to randomly play tracks on the current or
specified CD, except in continuous mode.
® Ail disc random (ALL DISC, CONTINUE, RANDOM)
Press the RANDOM button in continuous play mode to randomly select
and play tracks from all of the CDs in the CD changer.
Programmed play (using the remote control unit)
© Up to 20 tracks can be programmed to be played in any required order
from one CD or all CDs in the CD changer.
Example: (CD containing more than 12 tracks)
Example 1: Programming tracks from disc 1 (tracks 2, 5, and 12).
onl
Fee aes
1 2 a PROGRAM
TRACK,
a> 2 Fe] PROGRAM
2 3 PROGRAM
Program order number
“e = T70_NF
a > a Eee a
Bis 2 a PROGRAM
(7) C3 } CO number — Track number
PROGRAM cDe ut
@ Set to the CD mode.
@ Press the @ button.
@ Press the PROGRAM button to set to the programming mode.
@ Press the No. 1 CD CONTROL button.
@ Press to designate the required track number.
© Designate the remaining tracks by pressing the track number buttons.
@ Press the PROGRAM button to confirm program details.
® Repeat from step @ to readjust the program.
© Repeat from step @ to add to the program.
@ Press the CO »/81 button when programming is compisted.
Programmed play starts.
15
| 5/N3/3/a 290-O4