JVC RC-QC7 - Page 14

-(9€00 LON) pL
Continuous Playback
(Between Decks A and B)
Operate in the order shown
@ Load a cassette tape in Deck A.
@ Load a cassette tape in Deck B.
@ Set the reverse mode to (=).
O Select either Deck A or B.
@ Press the TAPE <1(> button to start continuous play.
(| RADIO RECEPTION S
Operate in the order shown :
® When AC power is used. (When battery power is used, switch on the
5/1 button first, then perform operation.)
@ Press the TUNER button.
© The power is switched on and a band and radio frequency will be
shown in the display.
@ Select the band.
@ Tune to the required station.
© Adjust.
FM STEREO AUTO/MONO button (using the remote control
unit)
Auto mode:
Set to this position when listening to or recording an FM stereo broadcast.
The STEREO indicator lights when the FM stereo broadcast is received.
MONO:
Set to this position when FM stereo reception is noisy.
When another station is tuned to in the MONO mode, the unit automatically
enters Auto mode.
18
@ To stop tape running, press the ™ button. When the reverse mode is
set to =, the tape will stop at the end of the side being played.
@ The DECK A/B button does not function unless tapes are loaded in
both decks.
FM STEREO AUTO/MONO button
Sas
Soe e
2 10 10
CGC @
Hoon
I~ BAN conmee
Bt.
Seek tuning
Press the ké<@ or BB button for one second or more. The unit enters
the seek tuning mode to tune in the nearest station automatically, so the
broadcast can be heard.
Manual tuning
Each time the @ or te1 button is pressed, the unit steps through the
current frequency band. Tuning is done in steps of SO kHz for FM and
9 kHz for AM.
Press to move to higher frequencies.
Press to move to lower frequencies.
Notes:
@ When seek tuning to the required station is not possible because the
broadcast signal is too weak, press the td or + button momentarily
to perform manual tuning.
® When the power is set to standby, or another mode (TAPE or CD) is
selected, the last tuned frequency is stored in memory. When the power
is switched on again and TUNER button is pressed, the same station
will be tuned to.
Auto preset tuning
This function scans the current band, detecting frequencies used to
broadcast signals, and stores the first 15 frequencies in memory
automatically.
@ Press the AUTO PRESET button for more than 2 seconds. The
frequencies of stations broadcasting signals can be stored in memory
automatically in the order of increasing frequency. (15 stations in each
band.)
Press for more than 2 seconds.
er. — AUTO
PRESET
Presetting the desired stations (using the remote control unit)
15 stations in each band can be preset as follows:
Example: (Presetting an FM station broadcasting on 103.5 MHz to preset
button “15")
@ Press the BAND button.
@ Select the FM band using the BAND button.
@ Tune to the required station.
© Press preset button “+10”, then “5” for more than 2 sec.
(When “15” biinks in the preset station display, the station has been
stored.)
© Repeat the above procedure for each of the other stations, using a
different preset button each time.
© Repeat the above procedure for the other band.
© To change preset stations
Perform step @ above after tuning to the required station.
Notes:
The previous stored station is erased when a new station is stored,
because the new station's frequency replaces the previous frequency
in memory.
® When listening to an AM broadcast, noise may be heard if the remote
control unit is used.
© All preset stations will be erased when the power cord is
m
disconnected
or
a
power
failure
occurs
for
more
than
48
hours.
In
(2S.
such cases,
store
the
stations
again.
Preset station tuning
{Receiving the preset stations)
® The stations must be preset before this operation can be performed.
sing the main unit)
Press the TUNER button.
@ Select the band using the TUNER button. @ Select the band using the BAND button.
@
Press
the
PRESET
TUNING
button
to
select
the
required
preset
@
Press
the
required
preset
station
buttons
(No.
1
—
No.
10
and
+10).
station. ® The preset station number and frequency corresponding to the button
pressed are shown.
Using the remote control unit)
Press the BAND button.
Using the antennas
AM
na
iN
Note:
The built-in ferrite core antenna can pick up interference from television
receivers in the neighborhood and thereby disturb AM reception.
19
ike 290-94