JVC RX-508VBK User Manual

RX-SO8VBK
RX-509VTN
Connecting the Power
Supply
Inserting Batteries into the
Remote Control
Replacing Batteries
Page 12
1-14 (No. 20376)
Connecting the Power
After checking all connections, insert the power cord plug into an outlet.
When the power supply is connected correctly, the POWER STANDBY indicator lights on the
front of the receiver. A smail amount of power (5 watts) is consumed under these conditions,
even if the receiver is tumed off. To shut off the power completely, unplug the power cord from
the outlet.
4X CAUTION!
* Do not handle the power cord with wet hands.
* Do not pull on the power cord to unplug the receiver. Always grasp the plug
directly so as not to damage the cord.
* Do not plug the power cord into a socket until all components are connected
correctly.
IMPORTANT! If the power cord is disconnected or a power failure occurs, the
receiver settings in memory are retained for 2 or 3 days.
The remote control requires two batteries (supplied). To insert batteries, follow these steps:
Step 1 On the back side of the remote control, press down on the battery cover and slide it
out.
Step 2 Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (-) to (-).
Step 3 Slide the cover in.
If the range or effectiveness of the remote control decreases, replace the batteries. Use two (2)
AAA (24F) dry-cell batteries of the RO3/UM-4 type.
4X CAUTION! Follow these precautions to avoid leaking or cracking cells:
¢ Place batteries in the remote control so they match the polarity indicated:
(+) $0 (+) ond (-) to (+.
° ea the correct type of batteries. Batteries that look similar may differ in
voltage.
© Always replace both batteries ot the same time.
* Do not expose batteries to heat or flame.
Operation Outline
(1 Tum on the power
Select speakers
(page 19)
(3) Choose an audio source
{page 14)
[@) Turn the surround sound
effect on or off
{pages 21-23}
[5] Operate the audio
source (pages 24-26)
© Adjust volume and tone
{pages 19-20}
RX-SO8VBK
RX-509VTN
Basic Operation Reference
Push the POWER switch to tum on the receiver. The display lights:
AM fof
if Wo 4 we
NOTE: Pushing the POWER switch again turns off the power and lights the STANDBY
light.
Use
the
SPEAKERS
switch
to
choose
between
the
two
sets
of
speakers.
To
use
your
headphones,
insert
the
headphone
plug
into
the
PHONES
jack
on
the
receiver.
To
choose
an
audio
source,
press
one
of
the
SOURCE
selector
buttons
on
the
receiver,
or
press
one
of
the
SOURCE
SELECT
buttons
on
the
remote
control.
i Tl
L J
Totum
the
surround
sound
effect
on or
off,
press
the
SURROUND
button.
When
the
surround
processor
is
activated,
one
of
the
effect
program
indicators
(PRO
LOGIC,
3CH
LOGIC,
or
HALL)
li
.
ights
up
SUA
ae
“in
a Lo
ew
Refer
to
the
manual
provided
with
each
component.
If
your
JVC
components
are
connected
to
the
COMPU
LINK
jack
of
the
receiver,
you
can
operate
them
using
the
remote
control.
Rotate
the
MASTER
VOLUME
control
on
the
receiver
or
press
the
VOLUME
button
on
the
remote
control
to
adjust
volume.
See
pages
19-20
for
other
ways
to
change
the
volume
or
tone.
Page 13
(No. 20376) 1-15

JVC RX-508VBK Specifications

General

Brand	JVC
Model	RX-508VBK
Category	Stereo Receiver
Language	English