Need help?Do you have a question about the JVC RX-308BK and is the answer not in the manual?
General| Power Output | 30 W per channel (8 ohms) |
|---|---|
| Total Harmonic Distortion | 0.1% |
| Input Sensitivity | 200 mV |
| Signal-to-Noise Ratio | 70 dB |
| Speaker Impedance | 4 - 16 ohms |
| Dimensions | 430 x 130 x 280 mm |
| Weight | 5.5 kg |
| Frequency Response | 20 Hz - 20 kHz |
| Tuning range | FM: 87.5 - 108 MHz |
| Speaker load impedance | 8Ω to 16Ω |
Emphasizes adherence to original design and authorized parts for safety.
Warns against alterations, which void warranty and relieve manufacturer responsibility.
Highlights special safety features of components and risks of using incorrect replacements.
Advises observing original lead routing for preventing shock and fire hazards.
Details procedures for testing electrical shock hazards after re-assembly.
Lists essential safety standards, repairer responsibility, and component checks.
Lists key features like monitor recording, surround, remote control, preset stations, ease of use.
Explains manual content, conventions for controls, display messages, important instructions, and cautions.
Identifies numbered switches and controls on the receiver unit.
Identifies numbered controls on the remote control.
General warnings before installation, including handling hands, power, and reading instructions.
Guidelines for placing the receiver, considering level, moisture, and temperature.
Safety warnings for handling the power cord and plugging it in.
Warnings against inserting metal objects, disassembly, or exposing to moisture.
General instruction to read paragraphs carefully before connecting.
Explains connecting components using RCA cables and notes on turntable connections.
Explains connecting JVC audio components for convenient operation.
Describes using the receiver's AC outlet to power other audio components.
Details how to connect up to four speakers for stereo and surround features, with a caution on impedance.
Instructions for connecting the supplied AM loop antenna.
Details on connecting an outdoor antenna for better AM reception.
Steps to connect the supplied temporary FM antenna.
Instructions for connecting a 300-ohm feeder-cable antenna.
Steps for connecting a 75-ohm coaxial-cable antenna, with a caution.
Instructions for plugging in the power cord and what happens when power is connected.
Steps to insert batteries into the remote control, noting polarity.
Guidance on when and how to replace remote control batteries, with safety precautions.
Outlines the basic steps for operating the receiver, from power on to volume adjustment.
Explains how to select audio sources for listening using receiver or remote buttons.
Describes how the source is selected for recording and notes on volume/tone adjustments.
Details how to use the Monitor feature to compare source and recording quality.
Explains how to tune to AM/FM stations using tuning buttons and describes manual vs. automatic tuning.
Describes switching between stereo and monaural reception modes.
Explains how to assign channel numbers (1-40) to radio stations.
Step-by-step guide for manually presetting favorite stations using the MEMORY button.
Steps to automatically preset up to 40 stations using the AUTO MEMORY button.
How to skip a station during automatic presetting.
How to adjust volume using the MASTER VOLUME control and remote, with a caution on loud sound.
Using the FADE MUTING button for quick volume reduction.
How to activate speaker pairs using SPEAKER buttons.
How to connect and use headphones, with a caution on volume.
Using the BALANCE control to adjust sound balance between left and right channels.
Using BASS and TREBLE controls to adjust low and high pitches for tone.
How to activate the surround feature with four speakers for a movie-theater effect.
Overview of operating JVC components via the receiver's remote.
How to use the remote control by pointing it at the receiver's sensor.
How the receiver automatically selects sources for playing and recording.
Steps for synchronized recording from CD/turntable to tape deck.
Notes on CD player and cassette deck turning on/off with the receiver.
Remote control operations for turntable playback and stop.
Remote control operations for CD playback, track skipping, and stopping.
Remote control operations for cassette playback, track skipping, stopping, and recording.
Remote control operations for VCR playback, stopping, and recording.
Using TAPE 1 in CONTROL section for cassette deck operations.
Using CD DISC button in CONTROL section to select disk.
A chart listing common problems, their possible causes, and solutions.
Detailed technical specifications for the receiver section.
Technical specifications for the FM tuner section.
Technical specifications for the AM tuner section.
General specifications including power requirements, dimensions, and weight.
Output power and distortion specs for universal amplifier section.
Output power and distortion specs for Europe, UK, Australia amplifier section.
To Next Page
