JVC RX-508VBK User Manual

RX-S09VTN
|
|
__RX-509VTN
Adjusting the Volume and Tone
eeeiiees en er eRe EE i. .
Assigning Names to Preset Stations Adjusting the Volume
Pec lai ® Baba id i a
Entering
Title
Characters
‘You
can
assign
a
title
of
up
to
four
characters
(for
example,
a
station
name)
to
each
preset
station
Using
the
MASTER
Use
the
MASTER
VOLUME
control
to
adjust
the
volume
from
the
left
and
right
speakers.
(1-20). When a preset station is called, its title is displayed in the display window along with VOLUME Control Rotating the dial to the right increases the volume. The volume from the speakers and the
its channel number. headphones increases simultaneously.
NOTE: Volume can also be adjusted using the remote control. Press the VOLUME
button marked + to increase the volume, oc the VOLUME button marked - 10
decrease the volume.
After selecting the preset channel (1-20), enter title characters as follows:
CHARACTER Step 1 Press the CHARACTER button.
C_) The cursor appears at the first character position.
IMPORTANT! You must press the CHARACTER button while a preseet number
eppears. You have about 2 seconds to do this. If the display returns to tuning ;
frequencies before you press the CHARACTER button, select the preset channel :
ZS CAUTION! Listening to extremely loud sound may damage your hearing. Be
especially careful when using headphones.
in.
:
=
!
Muting
the
Sound
Press
the
FADE
MUTING
button
on
the
remote
control
to
decrease
the
volume
easily
when
you
!
=
receive
a
phone
call
or
a
visitor.
i
PAPE
MINS
IMPORTANT!
If
you
are
listening
at
very
high
volume,
you
may
need
to
press
FADE
If
a
title
has
already
been
assigned,
the
first
character
blinks.
If
you
are
not
changing
MUTING
a
second
or
third
time
to
reduce
volume
completely.
this
character,
press
the
CHARACTER
button.
i
CHARAGTOR
NPT
Step
2
Using
the
DOWN
and
UP
buttons,
select
the
character
to
be
entered.
:
Selecting
the
Speakers
Pushing
in
SPEAKER
button
1
or
2
activates
that
pair
of
speakers.
Pressing
either
button
again
ems
ea
You
can
choose
from
the
characters
shown
below.
Pressing
the
DOWN
or
UP
button
is
gnaiaions
deactivates
that
pair
of
speakers.
When
the
button
is
in,
that
pair
is
activated.
You
can
listen
selects
the
next
character
in
the
sequence.
to
both
pairs,
pair
1,
pair
2,
or
neither
pair.
Oo
©)
IMPORTANT!
If
only
one
set
of
speakers
is
connected,
pressing
"in"
both
speaker
OR
OFF
buttons
will
produce
no
sound.
Listening to Headphones Insert the headphone plug into the PHONES jack. To limit sound to the headphones (no sound
from the speakers), press SPEAKER buttons 1 and 2 to deactivate all speakers.
PHONES
© A\ CAUTION! To avoid hearing damage, turn the volume down before plugging in
the headphones, then grodually increase the volume.
Step 3 When the desired character appears, press the CHARACTER button.
‘The
cursor
moves
to
the
next
character
position.
You
can
enter
up
to
four
characters
:
by
repeating
Steps
2
and
3.
i
Adjusting
the
Left
Right
Use
the
BALANCE
control
to
adjust
the
balance
between
the
left
and
right
channels,
Rotating
i Balance the dial to the right increases the right-channel volume, and rotating it to the left increases the
|
ulate
left-channe}
volume.
The
BALANCE
control
affects
both
sets
of
speakers
and
the
headphones.
A f i ial
ae" j . “
i ‘ .
ENTER
Step
4
Press
the
ENTER
button
to
save
the
selected
characters.
|
wre
ad
C |
Al Tow |
iv Ut |
\
Page
18
Page
19
1-20 (No. 20376)
(No. 20376) 1-21

JVC RX-508VBK Specifications

General

Brand	JVC
Model	RX-508VBK
Category	Stereo Receiver
Language	English