JVC UX-A4 - Synchronized recording with the CD player

UX-A4 B/E/G/GI/EN |
@ Insert a cassette with a suitable length (recording time)
with side A facing out.
@ The tape length can be set from the remote control.
(See below.)
@ Press the CD SYNCHRO REC button to start CD edit
recording.
@ Recording starts in the forward direction (on the side
facing out).
e During edit recording, the leader tape section
(approx first 10 sec.) is wound automatically and
then recording starts. The reverse mode is set to
> mode automatically.
@ The tape stops automatically when the CD has been
played.
e To change the tape length (recording time)
When the EDIT button is pressed while pressing the
SHIFT button with a CD loaded, the tape length required
to record the entire disc is displayed (C-46, C-54, C-60,
C-74 or C-90).
At this time, the displayed tape length can be changed
by pressing the track number buttons.
Example: To change to C-50
Press the +10 button four times, and within 10 seconds,
press the 10 button.
When the length of the tape is changed, some of the tunes
that were to be recorded on side A may be indicated as to
be recorded on side B or vice versa, according to the tape
length specified.
Depending on the tape length specified, some tunes may
not be recorded on the tape. Set the tape length (recording
time) so that the entire disc can be recorded.
Synchronized recording with the CD player
@ In this system, the CD player starts playback when the
cassette deck enters the recording mode.
Operate In the order shown
18 (No. 1890)
@
When
editing
a
disc
with
16
to
20
tunes
CD
editing
can
be
used
to
record
discs
containing
up
to
20
tunes,
however,
the
music
calendar
shows
up
to
only
15
tunes.
As
the
16th
to
20th
tunes
will
not
appear
in
the
music
calendar
display
(the
"OVER"
indicator
will
light),
be
sure
to
check
the
tunes
you
have
recorded
after
completing
editing.
e
Set
the
DOLBY
NR
as
required.
The
DOLBY
NR
indicator
lights.
Note:
The
optimum
sound
quality
will
not
be
obtained
If
different
DOLBY
NR
switch
settings
are
used
during
recording
and
playback.
Notes:
@
When
a
disc
with
21
tunes
or
more
Is
loaded,
°C---"
will
appear
in
the
display.
In
such
a
case,
set
the
required
tape
length
using
the
track
number
buttons
on
the
remote
control.
F
©
In
CD
edit
recording
blanks
of
approx.
4
seconds
will
automatically
be
left
between
tunes
on
the
recorded
tape.
When
automatic
spacing
between
tunes
Is
not
required ...
Perform the following.
4.
Press
the
C8
button
of
the
CD
player
twice.
The
CD
Player
enters
the
pause
mode.
2. Press
the
CD
SYNCHRO
REC
button
to
start
recording.
Note:
e
Depending
on
the
disc
used,
blanks
of
a
specified
length may be left between tunes
e After use
Press
the
™/CLEAR
button
to
release
the
CD
edit
recording
mode.
(The
CD
edit
recording
mode
Is
also
released when the CD door Is open.)
@ Load a disc and close the CD door. (The power is
switched on.)
@ Set to the CD mode.
© Load a cassette with side A facing out. (Wind past the
leader tape before starting recording.)
© When programmed playback Is required, program the
required tunes using the remote control. (See page 27.)
e Select tunes with a total playing time which does not
exceed the tape length.
© Select the required reverse mode( > or TF )
© Press the CD SYNCHRO REC button; synchronized
recording will start.
® Recording starts in the forward direction and CD play
starts automatically.