Why Kaco blueplanet 92.0 TL3 Inverter doesn't feed maximum power into the grid despite high radiation?
If your Kaco inverter isn't feeding maximum power into the grid despite high radiation, it could be due to particular ambient conditions. Ensure sufficient cooling of the unit. Also, remove any foreign bodies present on the device and clean the cooling fins.
What to do if the grid fuse trips with Kaco blueplanet 92.0 TL3?
If the grid fuse trips when using your Kaco Inverter, it may be because the grid fuse capacity is too low. Select a backup fuse with a capacity somewhat higher than the device’s maximum feed-in current. If this doesn't resolve the issue, there may be hardware damage, in which case you should contact KACO Service to test the hardware.
How to troubleshoot Kaco blueplanet 92.0 TL3 when the LEDs do not light up?
If the LEDs on your Kaco Inverter do not light up, it could be due to the grid voltage not being available. Check whether the DC and AC voltages are within the permitted limits. If the issue persists, notify KACO Service.
What to do if Kaco blueplanet 92.0 TL3 stops feeding into the grid shortly after being switched on?
If your Kaco Inverter stops feeding into the grid shortly after being switched on, even with sunlight present, the cause may be defective circuit-breakers in the device. Ensure that there is sufficient PV generator power. Another potential cause is a defective grid separation relay, which should be replaced by KACO Service. If neither of these solutions work, notify KACO Service.
Why is Kaco blueplanet 92.0 TL3 Inverter active but not connected to the grid?
If your Kaco Inverter is active but not connected to the grid, it might be due to a grid-feed interruption caused by a grid fault. Change the grid parameters within the permitted operating limits.
What causes an impossible daily peak value on Kaco blueplanet 92.0 TL3 Inverter display?
If your Kaco Inverter displays an impossible daily peak value, it is likely due to faults in the grid. To reset the value immediately, switch the device off by disconnecting it from the grid and switching off the DC, then switch it back on.
What does 'Fault in fan 2' mean on my Kaco blueplanet 92.0 TL3?
If your Kaco Inverter displays 'Fault in fan 2', the fan is malfunctioning. Notify KACO Service! With a defective fan, the power is reduced to 50% to avoid the device being destroyed.
What does 'Fault in fan 3' mean on my Kaco Inverter?
If your Kaco Inverter displays 'Fault in fan 3', the fan is malfunctioning. Notify KACO Service! With a defective fan, the power is reduced to 50% to avoid the device being destroyed.
What to do if there is a fault in fan 1 of Kaco Inverter?
If there is a fault in fan 1 of your Kaco Inverter, it means that the fan is malfunctioning. Replace defective fan.
Why don't daily yields correspond to the yields on the feed-in meter of Kaco blueplanet 92.0 TL3 Inverter?
If the daily yields on your Kaco Inverter do not correspond to the yields on the feed-in meter, it is due to tolerances of the measuring elements in the device. No action is required.
Provides detailed electrical specifications for various KACO blueplanet models.
Details safety considerations and requirements for choosing an installation site.
Provides safety instructions for lifting and securing the device after the mount is installed.
Provides instructions for making electrical connections, emphasizing compliance with standards.
Details the steps for preparing the AC connection, including cable routing and lug fitting.
Explains how to make the 4-pole grid connection for TN and TT systems.
Guides on checking the PV generator for ground faults to prevent electric shock.
Details safety warnings and steps for connecting the PV generator to the device.
Outlines various methods for starting up the device and its configuration.
Provides notes on ensuring DC power supply during initial start-up.
Details the monitoring interface of the device, including key areas and their functions.
Explains the menu structure, including password protection for grid parameters.
Explains the role of reactive power in grid stability and inverter contribution.
Lists and explains the implemented reactive power control functions.
Details active power limitation functions like P set and P limit.
Details voltage-dependent power reduction using characteristic curves.
Explains how the device responds to grid overfrequency for stability.
Details permanent power gradient limitations for plant operation.
Explains KACO's strategy for reliable island detection and prevention.
Provides steps for disconnecting AC and DC cables.
Lists general safety warnings and procedures for handling faults.
Details faults, causes, explanations, and remedies, categorizing actions.
Provides a table of status and fault messages displayed by the device.
General| Rated Power | 92000 W |
|---|---|
| Max. apparent AC power | 92000 VA |
| Maximum DC Input Voltage | 1100 V |
| AC voltage range | 320 V - 480 V |
| AC frequency | 50 Hz / 60 Hz |
| Nominal AC Voltage | 400 V |
| Power Factor | 0.8 leading - 0.8 lagging |
| THD | < 3 % |
| MPPT Voltage Range | 450 V - 850 V |
| Nominal AC Output Power | 92 kW |
| Maximum AC Output Power | 92 kW |
| Operating Temperature Range | -25°C to +60°C |
To Next Page
