To Next PageTo Next PageWhat to do if Kärcher BD 70/75 W Classic Bp Scrubber cleaning results are unsatisfactory?
If you're not happy with the cleaning results from your Kärcher Scrubber, here are a few things to try: * Reduce the driving speed. * Check the brushes for wear and replace them if needed. * Ensure that you are using the appropriate brush type and detergent for your cleaning task.
What to do if my Kärcher BD 70/75 W Classic Bp Scrubber suction turbine runs at an increased speed?
If the suction turbine on your Kärcher Scrubber is running at an increased speed, try the following: 1. Drain the waste water. 2. Clean the float. 3. Inspect the fluff filter and clean it if necessary. 4. Check the suction hose for clogs and clean if necessary. 5. Check the suction bar for clogs and remove any blockages.
How to start Kärcher Scrubber?
To start your Kärcher Scrubber, follow these steps: 1. Turn the key-operated switch to "1". 2. Actuate the safety switch. 3. Insert the battery plug. 4. Check the battery and charge if necessary. 5. Check that the battery terminals are correctly connected.
What to do if the brushes do not rotate on my Kärcher BD 70/75 W Classic Bp Scrubber?
If the brushes on your Kärcher Scrubber aren't rotating, check to see if they are blocked by a foreign object and remove it.
Why is the water volume insufficient in my Kärcher BD 70/75 W Classic Bp?
If the water volume in your Kärcher Scrubber is insufficient, take these steps: 1. Check the fresh water filling level and fill the tank if needed. 2. Increase the water volume using the water volume regulating knob. 3. Clean the fresh water filter. 4. Check the hoses for any clogs and clean them if necessary.
What to do if my Kärcher BD 70/75 W Classic Bp Scrubber vibrates during cleaning?
If your Kärcher Scrubber vibrates during cleaning, try using a softer brush.
What to do if the water volume is insufficient in my Kärcher BD 70/75 W Classic Bp?
If the water volume is insufficient in your Kärcher Scrubber, take these steps: Begin by checking the fresh water filling level and refill the tank if needed. Increase the water volume using the water volume regulating knob. If you have a BR variant, pull off the water distribution strip on the cleaning head and clean the water channel. Clean the fresh water filter. Lastly, check the hoses for any clogging and clean them if necessary.
Why are the cleaning results unsatisfactory with my Kärcher BD 70/75 W Classic Bp Scrubber?
If the cleaning results of your Kärcher Scrubber are unsatisfactory, try the following: Reduce your driving speed. Check the brushes for wear and replace them if needed. Also, ensure that you are using a suitable brush type and detergent for the task.
What to do if the suction turbine runs at an increased speed in my Kärcher BD 70/75 W Classic Bp Scrubber?
If the suction turbine in your Kärcher Scrubber runs at an increased speed, follow these steps: First, drain the waste water. Then, clean the float. Check the fluff filter and clean it if necessary. Inspect the suction hose for any clogs and remove them. Finally, check the suction bar for clogging and remove any obstructions.
What to do if Kärcher Floor Machine suction performance is too low?
If the suction performance of your Kärcher Floor Machine is too low, try these steps: First, shut down the device and drain the waste water. Then, clean the seals between the waste water tank and the cover, checking for leaks and replacing if necessary. Ensure the suction hose is correctly connected to the waste water tank. Check and clean the fluff filter, and inspect/clean/turn over/replace the suction lips at the suction bar. Make sure the cap on the waste water drain hose is closed and the suction bar is adjusted correctly. Clear any clogging in the suction hose, ensuring the white marking on the hose aligns with the retaining clip when refitting. Finally, check the suction hose for leaks, replacing it if needed.
General| Working width (brush) | 700 mm |
|---|---|
| Battery Voltage | 24 V |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Working width (vacuum) | 750 mm |
| Brush speed | 180 rpm |
