Keithley 2601 Reference Manual

Index Series 2600 System SourceMeter® Instruments Reference Manual
I-4 2600S-901-01 Rev. C / January 2008
Commands .......................................6-4
Considerations .................................6-4
Limitations ........................................6-3
Low limits ..........................................6-3
Manual ..............................................6-3
Programming ....................................6-4
Programming example .....................6-5
Reading buffers ......................................12-5
Readings
Maximum ..........................................6-3
Recalling ...........................................7-3
Requesting ...........................1-24, 4-10
Storing ..............................................7-3
Rear panel summaries .............................1-9
Recalling readings ....................................7-3
Recommended test equipment ..............15-3
Recommended verification equipment ...15-3
Registers
Enable and transition ..................... D-13
Measurement event ....................... D-24
Operation event ............................. D-18
Programming example .................. D-27
Questionable event ....................... D-21
Reading ......................................... D-10
Serial polling and SRQ .................. D-12
Service request enable .................. D-12
Standard event .............................. D-16
Status sets ..................................... D-15
System summary event ................. D-15
Rel ............................................................6-8
Defining a value ................................6-8
Enabling and disabling .....................6-8
Front panel .......................................6-8
Remote programming .......................6-9
REM .......................................................11-7
Remote calibration .................................16-5
Remote operation
Source-measure procedure ..............4-9
Remote programming .............................1-24
Ohms ..............................................4-15
Power ...................................4-16, 4-18
Remote TSP-Link synchroniaztion
line commands .....................................10-10
Removing Stale Buffers ..........................9-12
REN (remote enable) .............................11-6
Restoring factory defaults .......................15-4
Rise time ................................................8-22
Rotary knob ..............................................1-8
RS-232 cable ............................................1-5
RS-232 Interface
Terminator ......................................11-9
RS-232 interface
Baud rate ........................................11-9
Connections .................................11-11
Data bits .......................................11-10
Flow control ..................................11-10
Operation ........................................11-8
Parity ............................................11-10
Sending and receiving data ............11-9
Run-time environment ......................2-3, 2-7
Memory considerations ..................2-44
S
Safety shield .......................................... 3-16
Safety symbols and terms ........................ 1-3
Script management ................................ 2-40
Scripting ................................................... 2-3
Scripting Language .................................. 2-3
Scripts ..............................................2-4, 2-6
Creating ......................................... 2-15
Creating functions ............................ 2-5
Factory scripts ................................ 2-42
Importing ........................................ 2-24
Launch configuration ...................... 2-19
Launching ...................................... 2-22
Modifying ........................................ 2-15
Programming model ......................... 2-9
Retrieving from Model 260x ........... 2-23
Saving ............................................ 2-16
User ............................................... 2-34
Scripts, named ......................................... 2-4
SDC (selective device clear) .................. 11-7
Selecting an interface ............................ 11-2
Sensing .................................................... 3-5
2-wire local ....................................... 3-6
4-wire remote ................................... 3-7
Mode selection ................................. 3-8
Ohms ............................................. 4-13
Serial polling ..........................................D-12
Setting the measurement range ............. 15-6
Setting the source range and
output value ........................................... 15-5
Settling time considerations ................... 8-23
Setups
Front panel ..................................... 1-21
Power-on ........................................ 1-22
Restoring ........................................ 1-21
User ............................................... 1-21
Shielding
Noise .............................................. 3-13
Safety ............................................. 3-16
Sink .......................................................... 8-7
Sink operation ........................................ 4-12
SMU connections ................................... 3-10
Source ...................................................... 8-7
Source I measure I ................................. 8-16
Source V measure V .............................. 8-16
Source-measure capabilities .................... 4-2
Source-measure procedure
Front panel operation ....................... 4-8
Programming example ................... 4-10
Remote operation ............................ 4-9
SPE, SPD (serial polling) ....................... 11-7
Specifications ...........................................A-1
Speed ....................................................... 6-6
Command ........................................ 6-7
Configuration menu .......................... 6-7
Programming example ..................... 6-7
Remote programming ...................... 6-7
Setting .............................................. 6-7
SRQ (Service Request) .............. 11-8, D-10
Staircase sweeps ..................................... 8-3
Standard libraries ................................... 2-53
Status byte and service request (SRQ) .D-10
Status byte and service request
commands .............................................D-12

Keithley 2601 Specifications

General

Brand	Keithley
Model	2601
Category	Measuring Instruments
Language	English