Kelso KCM65 - User Manual

Questions and Answers

C
Cindy PughAug 3, 2025
Why Kelso Construction Equipment power tool will not start?
- A
  Alicia CrosbyAug 3, 2025
  If your Kelso Construction Equipment power tool won't start, there are several potential causes: * The power cord may not be properly plugged in; ensure all electrical cords are connected to the mains power. * The power switch might not be in the on position; make sure all switches on the power tool and mains power are on. * The power source could be incorrect; verify the power tool is connected to the correct power source as indicated on the name plate. * The circuit breaker may have shut off; check and reset the circuit breaker, inspecting power cords for damage. Damaged electrical switch or motor. * The electrical switch or motor may be damaged; in these cases, have the power tool repaired by a qualified electrician at an authorized service center.
J
Jeremy AyersAug 7, 2025
What to do if Kelso KCM65 power tool does not reach full power?
- N
  nlopezAug 7, 2025
  If your Kelso Construction Equipment power tool isn't reaching full power, consider these possibilities: * The mixing volume might be too large; try reducing the amount of material in the mixing bowl. * The extension cord may not be suitable; use a heavy-duty extension cord that is less than 25m. * The power source voltage could be too low; connect to another power source. * The motor might be worn; in this case, repair or replace the worn motor.
E
Erica PowersAug 12, 2025
Why did my Kelso Construction Equipment power tool automatically switch off?
- D
  Dr. Daniel RiveraAug 12, 2025
  Your Kelso Construction Equipment power tool may automatically switch off due to a few reasons: * The power cord may not be plugged in properly; ensure all electrical cords are connected to the mains power. * The motor may be overheated; this is normal as temperature-dependent overload protection has engaged, so wait for the power tool to cool down. * The circuit breaker may have been engaged; check that the circuit and switches are active, then restart the tool.
J
Jessica LeonardAug 16, 2025
Why Kelso KCM65 mixing bowl will not rotate under load?
- J
  James HarrisAug 16, 2025
  If the mixing bowl of your Kelso Construction Equipment doesn't rotate under load: * The mixing bowl may be overloaded; turn off the power tool and completely empty the mixing bowl, then turn the power tool back on to check. * The V-belt might be slipping; turn off the power tool and refer to the instructions on how to check the V-belt. If the belt is damaged, replace it. * The pinion gear might not be turning; check the connection between the pinion shaft and the upper pulley, as well as the connection between the pinion gear head and shaft. * The gears may not be engaged; turn off the power tool and perform a visual inspection of the pinion gear, correcting the alignment. Replace the part if the gear is damaged.
K
kellypatriciaAug 20, 2025
How to fix Kelso KCM65 mixing bowl that will not tip?
- J
  Jocelyn NguyenAug 20, 2025
  If the mixing bowl of your Kelso Construction Equipment will not tip: * The bearing arm housing might be over-tightened; turn off the power tool, loosen the bolts, and re-check. * There may be no lubrication; turn off the power tool, check, and apply grease via the grease nipple. * The bearing arm could have interference; turn off the power tool and perform a visual inspection for foreign objects.
B
brenda21Aug 25, 2025
What causes unusual noise in Kelso Construction Equipment?
- A
  Alex BeltranAug 26, 2025
  Unusual or excessive noise in your Kelso Construction Equipment can be caused by: * Loose fasteners; check and tighten all bolts and nuts. * Incorrectly aligned pulleys; turn off the power tool and refer to instructions on how to check the V-belt. Replace the belt if damaged. * Lack of lubrication; turn off the power tool and lubricate the tilting shaft via the grease nipple, applying grease to the bowl shaft. * Gears not engaged correctly; turn off the power tool and inspect the gear ring and pinion gear for alignment and signs of wear. * Worn bearings; turn off the power tool and replace worn or noisy bearings.
D
Donald ButlerAug 29, 2025
What to do if Kelso KCM65 Construction Equipment mixing bowl does not rotate when empty?
- J
  jamessmithAug 29, 2025
  If the mixing bowl of your Kelso Construction Equipment does not rotate when empty: * The motor might not be running; refer to the troubleshooting steps for the problem 'The power tool will not start'. * The gears may not be engaged; turn off the power tool and perform a visual inspection of the pinion gear and correct the alignment. If the gear is damaged, replace the part. * The V-belt could be slipping; turn off the power tool and refer to instructions on how to do a check of the V-belt. If the belt is damaged, replace the part. * The pinion gear might not be turning; check the connection between the pinion shaft and the upper pulley, and also check the connection between the pinion gear head and shaft.

Summary

Technical Data

Product Overview

Product Introduction

Product Symbols Explained

Explains the meaning of various symbols used on the product and in the manual.

Intended Use of the Mixer

Describes the specific materials and applications the power tool is designed for.

Power Supply Requirements

Details the electrical specifications and connection requirements for the power tool.

Safety Guidelines

Safety Definitions and Warnings

Defines warning symbols and provides general safety instruction principles.

General Safety Instructions

Outlines essential safety rules for operating the power tool safely.

Work Area Safety Precautions

Covers maintaining a safe and hazard-free environment during operation.

Operational Safety Instructions

Specific safety rules to follow during the actual operation of the equipment.

Personal Protective Equipment (PPE)

Specifies essential protective gear required for safe operation and handling.

Safety When Working With Wet Concrete

Highlights hazards and precautions when mixing or handling wet concrete.

Understanding Operational Risks

Explains the inherent risks associated with the product's use.

First Aid Procedures

Provides immediate first aid measures for common injuries or exposures.

Dust Safety Precautions

Details safety measures to mitigate risks associated with airborne dust.

Noise Safety and Hearing Protection

Addresses noise hazards and the importance of hearing protection.

Vibration Safety Guidelines

Explains vibration risks and precautions to prevent equipment damage.

Maintenance Safety Instructions

Outlines safety procedures to follow during maintenance and repair.

Equipment Operation

Operating the Power Tool

Step-by-step guide on how to use the power tool safely and effectively.

Switching Power Tool On and Off

Instructions on the correct procedure for starting and stopping the mixer.

Loading the Mixing Bowl Safely

Guidelines for safely adding materials to the mixing bowl.

Emptying the Mixing Bowl

Procedures for safely emptying the contents of the mixing bowl.

Transportation Safety and Methods

Precautions and methods for safely moving the equipment.

Product Storage Guidelines

Recommendations for storing the equipment to ensure longevity and safety.

Product and Packaging Disposal

Guidance on environmentally sound methods for disposing of the product and packaging.

Service and Maintenance

Maintenance Schedule

A table outlining routine maintenance tasks and their frequency.

General Inspection Procedures

Steps for performing regular visual checks on the equipment.

Repair Maintenance Guidelines

Rules and precautions for carrying out repairs on the power tool.

Checking V-Belt Tension

How to inspect and ensure the V-belt is correctly tensioned for optimal performance.

Adjusting Gear Engagement

Instructions on how to properly adjust the gear engagement for smooth operation.

Applying Grease to Tipping Arm

Instructions on how to lubricate the tipping arm mechanism.

Cleaning the Power Tool

Detailed steps for cleaning the mixer after use.

Spare Parts List

Troubleshooting Guide

Kelso Warranty Policy

Two Year Limited Warranty

Details the terms, conditions, and coverage of the standard product warranty.

Thirty Day Limited Warranty on Repairs

Outlines the warranty coverage for specific repair work performed on Kelso products.

General Warranty Qualifications

States conditions under which warranty claims are assessed and processed.

Australian Consumer Law Rights

Explains consumer rights related to product guarantees under Australian law.

Kelso KCM65 Specifications

General

Brand	Kelso
Model	KCM65
Category	Construction Equipment
Language	English

Related product manuals

Kelso KC3.5FT

12 pages