18
■ WRINKLE GUARD
®
90 is preset to OFF. The Auto Dry cycles
will retain the WRINKLE GUARD
®
90 setting. For example, if
you select WRINKLE GUARD
®
90 in the Normal cycle,
WRINKLE GUARD
®
90 will be on the next time you select the
Normal cycle.
NOTE: WRINKLE GUARD
®
90 must be selected with a cycle in
order to work. If you do not select WRINKLE GUARD
®
90, the
dryer stops after cool down.
Cycle Signal
The Cycle Signal produces an audible sound when the drying
cycle is finished. Promptly removing clothes at the end of the
cycle reduces wrinkling.
Press CYCLE SIGNAL to turn the signal off.
NOTE: When WRINKLE GUARD
®
90 is selected and the Cycle
Signal is on, a tone sounds every 5 minutes until the clothes are
removed, or WRINKLE GUARD
®
90 ends.
Changing Cycles, Options and Modifiers
You can change Auto Cycles, Timed Cycles, Modifiers and
Options anytime before pressing Start.
■ Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press STOP twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press STOP once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Stop twice, the program clears and
your dryer shuts down. Restart the selection process.
TUMBLE FREE™ Non-Heated Dryer Rack
The dryer rack is shipped in place in your dryer. Remove and
discard any packing material before use.
Use the TUMBLE FREE™ Non-Heated Dryer Rack for items that
you do not want to tumble dry, such as sweaters.
To use the dryer rack
Do not remove the lint screen.
1. Open dryer door.
2. Place dryer rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of dryer rack to secure over the lint screen.
3. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the rack.
4. Close the door.
5. Press the POWER button.
6. Select a timed cycle and temperature (see following chart).
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using the Air Only temperature setting.
7. You may change the cycle time by pressing MORE TIME or
LESS TIME. Reset time as needed to complete drying. Refer
to the following table.
8. Press (and hold) START button (about 3 seconds).
NOTE: You must remove rack for normal tumbling. Do not use
automatic cycles with the dryer rack.
This chart shows examples of items that can be rack dried and
the suggested temperature setting and drying time. Actual drying
time will depend on the amount of moisture items hold.
*(Minutes) Reset time to complete drying, if needed.
A. Front edge
A
A. Dryer rack front edge
B. Dryer back panel
Rack Dry Setting Temp. Time*
Wool Sweaters
Block to shape and lay flat on
the rack.
Timed
Cycles
Low 60
Stuffed toys or pillows
Cotton or polyester fiber filled
Timed
cycles
Low 60
Stuffed toys or pillows
Foam rubber filled
Timed
cycles
Air Only
(no
heat)
90
Sneakers or canvas shoes Timed
cycles
Air Only
(no
heat)
90
A
B
To Next Page
Loading...
Need help?
General