EasyManua.ls Logo

Kenmore 153.582400 - User Manual

Kenmore 153.582400
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Use & Care Guide
Model No.
153.582400 40 Gallon Tall
153.582500 50 Gallon Tall
P/N 100263002 (0215)
Sears Brands Management Corporation,
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
LOW LEAD
CONTENT
Kenmore®
Electric
Water Heater
For potable water heating only.
Not suitable for space heating.
INSTALLER: Affi x these instructions to or near
the water heater.
OWNER: Retain these instructions for future
reference.
Si no puede leer o entender el inglés y necesita el manual de
instrucciones en español, puede solicitarlo al 1-800-821-2017. NO
TRATE DE INSTALAR U OPERAR ESTE CALENTADOR DE AGUA
SI NO ENTIENDE LAS INSTRUCCIONES. No hacer caso de esta
advertencia podría originar lesiones graves o mortales.
ADVERTENCIA

Table of Contents

Questions and Answers

  • M
    Melissa AndersonAug 2, 2025
    Why is there not enough or no hot water in my Kenmore 153.582400 Water Heater?
    • S
      Samuel RodriguezAug 2, 2025
      Several factors can cause a lack of hot water. First, ensure the cold water supply valve is completely open and that the electrical supply to your water heater is turned 'ON'. Check for any loose or blown fuses in the water heater circuit, and make sure the disconnect switch, if present, is in the 'ON' position. Verify that the electric service to your house hasn't been interrupted. Also, confirm that the thermostat is set to the desired temperature. During very cold weather, the incoming water will be colder, and the hot water usage may exceed the water heater's capacity. If you recently experienced very hot water followed by no hot water, the high-temperature shut-off system may be the cause.
  • M
    Mr. Sean Keller DDSAug 7, 2025
    What to do if my Kenmore 153.582400 Water Heater's water is too hot?
    • S
      shatfieldAug 7, 2025
      If the water from your Kenmore Water Heater is too hot, adjust the thermostat to a lower setting.
  • J
    James LongAug 14, 2025
    What to do if my Kenmore Water Heater T&P valve is dripping?
    • C
      Christopher FosterAug 14, 2025
      A dripping T&P valve on your Kenmore Water Heater can be due to several reasons. It may be caused by excessive water pressure, which can be resolved by using a pressure-reducing valve and a pressure relief valve. Another cause could be a closed system. Also, the T&P valve itself might be defective and need replacement.
  • T
    thomasjamieAug 26, 2025
    How to get rid of hydrogen gas in hot water faucets of Kenmore 153.582400 Water Heater?
    • C
      Collin JacksonAug 26, 2025
      To prevent any potential harm from hydrogen gas in your hot water faucets, it is recommended to open the hot water faucet and let it run for several minutes.
  • C
    candace31Sep 10, 2025
    Why does my Kenmore Water Heater have a rumbling noise?
    • A
      Angela GallagherSep 12, 2025
      A rumbling noise in your Kenmore Water Heater is likely due to scale or mineral deposits. To resolve this, clean and replace the elements by following the 'Element Cleaning/Replacement' instructions.

Summary

SAFE INSTALLATION, USE AND SERVICE

GENERAL SAFETY

PRODUCT SPECIFICATIONS

INSTALLATION INSTRUCTIONS

Facts to Consider About the Location

Wiring

Instructions and warnings for electrical connections and wiring the unit.

Wiring Diagram

Visual representation of electrical connections for the water heater.

Water Piping

Details on connecting water lines, including safety precautions.

Temperature-Pressure Relief Valve

Information on the proper installation and operation of the T&P relief valve.

Filling the Water Heater

Procedure for filling the water heater tank with water before powering on.

Installation Checklist

OPERATING YOUR WATER HEATER

Water Heater Start-Up

Water Temperature Regulation

How to set and manage the water temperature for safety and efficiency.

Safety Shut-Off

Modes and Adjustments

WATER TEMPERATURE ADJUSTMENT

OPERATING MODE DESCRIPTIONS

The Electronic Thermostat

Diagnostic LED Light

SERVICE AND ADJUSTMENT

Anode Rod Inspection

Temperature-Pressure Relief Valve Operation

Instructions for manually operating the T&P relief valve annually for safety.

Draining and Flushing

Heating Element Replacement

Step-by-step guide for replacing the heating elements.

TROUBLESHOOTING

Start Up Conditions

CLOSED SYSTEM;THERMAL EXPANSION

SMELLY WATER

HIGH TEMPERATURE SHUT OFF SYSTEM

NOT ENOUGH OR NO HOT WATER

Troubleshooting steps for lack of hot water or insufficient hot water supply.

WATER IS TOO HOT

Solutions for water temperature being excessively high.

STACKING

Diagnostic Code Chart: Energy Saver Module (ESM)

Diagnostic Code Chart: Electronic Thermostat (ET)

Troubleshooting Chart

LEAKAGE CHECKPOINTS

Kenmore 153.582400 Specifications

General IconGeneral
BrandKenmore
Model Number153.582400
TypeElectric
Capacity40 gallons
Voltage240 V
Wattage4500 W
Warranty6 years
Recovery Rate21 gallons per hour
Weight120 lbs

Related product manuals