Kenmore 6010 User Manual

®
FOO WASTE DISPOSERS
J
Installation, Care & Use Manual
TOOLS AND MATERIALS YOU WILL NEED:
Slotted Screwdriver, Adjustable Pliers, Plumber's Putty,
Electrical Tape
TOOLS, MATERIALS, AND ACCESSORIES
YOU MAY NEED:
Phillips Screwdriver, Drain Auger, 3/8" Electrical Clamp
Connector, Wire Nuts (2), Second 1 1/2" Drain Trap,
Hammer, Hacksaw, Water Hose Clamp, Pipe Wrench,
Copper Ground Wire, Dishwasher Drain Connection Kit, Air
Gap, Electrical On/Off Switch, Drain Tube Extension
Read through the entire installation, Care
& Use manual before installing the dis-
poser. Determine which of the tools,
materials, and accessories you will need
before you begin. Make sure you have all
necessary disposer parts before install=
ing the disposer (see part identification
diagram below).
O s j/K OR
'LT-- _t _,-f",_P -
1 <=_-'"-Je .................. fl/r,l. _-N
0_ _ U
Mounting Assembly Disposer Two-Bolt Discharge
A: Stopper H: MountingGasket/SplashBaffle N:Bolt(2)
B:Sink Flange h LowerMounting Ring ._lr O:Discharge Tube (1-1/2" Diam.)
C:FiberGasket J: DishwasherInlet " = P: Flange
D: Backup Ring K: Discharge Outlet Q:Gasket
E: MountingRing L: Wrenchette OF{
F:Screws(3) -- One-Bolt Discharge
G: Snap Ring N:Bolt
,_ O: Discharge Tube (1-1/2" Diam.)
•"-- p::Flanget
SAFETY SYMBOLS
Danger indicates an
imminently hazardous situation which,
if not avoided, will result in death or
serious injury.
I_iWARNING I Warning indicates
a potentially hazardous situation
which, if not avoided, could result in
death or serious injury.
I _,CAUTIONI Caution indicates a
potentially hazardous situation which,
if not avoided, may result in minor or
moderate injury.
Part No. 73110 - 1/02

Kenmore 6010 Specifications

General

Brand	Kenmore
Model	6010
Category	Garbage Disposal
Language	English

Summary

Safety Symbols

Installation Instructions

Check Installation Dimensions

Verify disposer and sink dimensions before installation.

Disconnect Sink Drain

Disconnect the existing drain trap and sink flange.

Disassemble New Disposer Mounting Assembly

Take apart the new disposer's mounting assembly for installation.

Install Flange in Sink Hole

Prepare and insert the sink flange into the sink drain hole.

Attach Upper Mounting Assembly to Sink Flange

Connect the disposer's upper mounting assembly to the sink flange.

Remove Existing Disposer

Safely remove the old disposer from the sink assembly.

Clean Sink Drain Line

Ensure the sink drain line is clear of blockages before proceeding.

Prepare Dishwasher Drain Connection

Prepare the disposer for a dishwasher connection if needed.

Connect Disposer to Electrical Supply

Connect the disposer safely to the electrical power source.

Connect Disposer to Mounting Assembly

Mount the disposer onto the sink's assembly.

Attach Discharge Tube to Waste Drain Line

Connect the disposer's discharge tube to the drain line.

Connect Dishwasher Drain

Connect the dishwasher drain hose to the disposer.

Attach Specification Decal

Apply the disposer specification decal for service information.

Safety Instructions and Precautions

Operating Instructions

Continuous Feed Disposers

Operating steps for continuous feed disposer models.

Batch Feed Disposers

Operating steps for batch feed disposer models.

Cleaning and Maintenance

Cleaning the Disposer

Instructions for cleaning the disposer's grind chamber and baffle.

Releasing a Disposer Jam

Steps to release a jammed disposer motor.

Kenmore Food Waste Disposer Warranty