Kenmore 6600 - User Manual

Questions and Answers

J
Jennifer HarrisonAug 15, 2025
Why are my clothes not drying in Kenmore 6600 Dryer?
- S
  Stacy LopezAug 15, 2025
  Several factors can cause clothes to not dry properly or take too long in your Kenmore dryer. The lint screen might be clogged, so clean it before each load. Ensure you've selected the appropriate cycle, and avoid overloading the dryer, which prevents proper tumbling. Check for obstructions in the exhaust vent or hood and ensure it's the correct length and diameter. Also, fabric softener sheets may be blocking the grill, and the dryer should be in a room with a temperature above 45ºF (7ºC) with adequate ventilation.
M
Michael JonesAug 18, 2025
What to do if Kenmore Dryer won't start?
- J
  James Shaw DDSAug 19, 2025
  If your Kenmore dryer isn't starting, first, ensure the door is completely closed. Then, press and hold the START/PAUSE button until you hear the drum moving. Check your household fuses or circuit breakers, as electric dryers use two. Replace both fuses or reset the breaker. If it continues, the dryer might not have the correct power supply (electric dryers need 240-volt), or you might be using the wrong type of fuse (use a time-delay fuse). If issues persist, consult a qualified electrician.
M
Michael HarringtonAug 21, 2025
Why does my Kenmore 6600 make unusual noises?
- M
  myersreneeAug 22, 2025
  Unusual sounds from your Kenmore dryer can stem from a few causes. If the dryer hasn't been used recently, a thumping sound might occur initially. Check for items like coins or buttons caught between the drum and the dryer's front or rear. For gas dryers, a clicking gas valve is normal. Ensure the dryer is correctly installed and leveled. Also, knotted clothing can cause bouncing and vibration, so separate items and restart the dryer.
M
Michael SanchezAug 25, 2025
Why is my Kenmore 6600 not heating?
- M
  morenowilliamAug 26, 2025
  If your Kenmore dryer isn't heating, even if the drum is turning, start by checking your household fuses or circuit breakers, as electric dryers use two. Replace both fuses or reset the circuit breaker. For gas dryers, ensure the valve on the supply line is open. Electric dryers require a 240-volt power supply, so you might need to consult a qualified electrician.
S
stephenskathrynAug 28, 2025
How to prevent lint on clothes from Kenmore Dryer?
- J
  jamieburchAug 28, 2025
  To prevent lint on your clothes when using your Kenmore dryer, ensure that the lint screen is cleaned before each load.
K
Kenneth StricklandAug 31, 2025
Why is the load too hot in my Kenmore 6600 Dryer?
- L
  Lisa MillsAug 31, 2025
  If your laundry items are too hot when removed from your Kenmore dryer, allow the Cool Down cycle to finish. This cycle reduces wrinkling and makes items easier to handle. Also, avoid using high-temperature cycles; instead, select a lower temperature or an Auto Dry cycle, which senses temperature or moisture and shuts off to prevent overdrying.
R
Robert KingSep 4, 2025
Why is the Kenmore 6600 cycle time too short?
- B
  Belinda RobertsonSep 4, 2025
  If your Kenmore dryer's automatic cycle is ending too early, it might be because the load isn't contacting the sensor strips properly. Try leveling the dryer. For very small loads, use Time Dry. Adjust the dryness level setting on Auto Dry Cycles; increasing or decreasing it will alter the cycle's drying time. If loads consistently end too early, consult the section on changing the Auto Dry Cycle Default Settings.
C
Charles MeltonSep 7, 2025
How to prevent wrinkled loads in Kenmore Dryer?
- R
  Ryan MacdonaldSep 7, 2025
  To avoid wrinkled loads in your Kenmore dryer, promptly remove clothes at the end of the cycle. Use the Wrinkle Guard™ feature to tumble the load without heat. Also, avoid overloading the dryer; smaller loads can tumble more freely, reducing wrinkles.
R
robbinsyolandaSep 12, 2025
Why does my Kenmore 6600 Dryer have odors?
- C
  Christian LeonardSep 12, 2025
  Odors in your Kenmore dryer can arise from a few sources. If you've recently been painting, staining, or varnishing nearby, ventilate the area and rewash/dry the clothing once the odors are gone. A new electric dryer may emit an odor from the heating element, which should dissipate after the first cycle.