Kenmore PG-40611S0L User Manual (English)

Other manuals for Kenmore PG-40611S0L

Questions and Answers:

D
Dana Martinez DDSAug 18, 2025
Why is my Kenmore Grill not getting hot enough?
- K
  kramosAug 18, 2025
  If your Kenmore Grill is only reaching 250-300 degrees, this often happens when the control knobs are turned on before the LP tank valve. This activates the gas regulator safety device. To fix this: * Open the grill lid. * Turn off all knobs on the control panel. * Turn off the tank knob. * Disconnect the regulator from the LP tank and wait 30 seconds. * Reconnect the regulator to the LP tank. * Slowly open the LP tank knob all the way (without excessive force). * Turn on the appropriate control knob and light the grill per the lighting instructions.
L
Laura BrownAug 20, 2025
What to do if flames blow out on Kenmore PG-40611S0L?
- D
  Devon BrownAug 20, 2025
  If the flames on your Kenmore Grill blow out, it could be due to a few reasons. High or gusting winds can cause this; try turning the grill so that the front faces the wind, or increase the flame height. Another cause could be low LP gas, so refill the LP tank. Also, the excess flow valve might have tripped; refer to the “Sudden drop in gas flow” section for guidance.
A
anna71Aug 23, 2025
What causes flare-ups on a Kenmore PG-40611S0L Grill and how to prevent them?
- L
  lindseyadamAug 23, 2025
  Flare-ups on your Kenmore Grill can be caused by drip buildup, excessive fat in the meat, or excessive cooking temperature. To address this, clean the burners and the inside of the grill/firebox. Trim the fat from the meat before grilling, and adjust to a lower cooking temperature.
D
Debra CrawfordAug 26, 2025
What to do if there's a sudden drop in gas flow in my Kenmore PG-40611S0L Grill?
- L
  Laura BishopAug 26, 2025
  A sudden drop in gas flow or low flame in your Kenmore Grill could be due to several reasons. First, check for gas in the LP tank. If that's not the issue, the excess flow valve might have tripped: turn off the knobs, wait 30 seconds, and light the grill. If the flames are still low, turn off the knobs and LP tank valve, disconnect and reconnect the regulator, perform a leak-test, then turn on the LP tank valve, wait 30 seconds, and light the grill. Lastly, a vapor lock could be the cause: turn off the knobs and the LP tank valve, disconnect the coupling nut from the tank, reconnect it, and retry.
S
Shannon BerryAug 28, 2025
Why won't my Kenmore PG-40611S0L burner light with a match?
- D
  Donna PorterAug 28, 2025
  If your Kenmore Grill burner won't light with a match, it could be because the match won't reach; use a long-stem match (fireplace match). It could also be due to improper match-lighting; see the “Match-Lighting” section on page 9 of the Use and Care.
J
Jill McdonaldAug 30, 2025
What to do if my Kenmore PG-40611S0L Grill has a persistent drip fire?
- R
  rpatrickAug 30, 2025
  If your Kenmore Grill has a persistent drip fire, it's likely due to drips trapped by food buildup around the burner system. Turn the knobs to OFF and the gas in the LP tank off. Leave the lid in position and let the fire burn out. After the grill cools, remove and clean all parts.
I
iphelpsSep 2, 2025
What to do if my Kenmore PG-40611S0L Grill has flashback fire in burner tubes?
- K
  Kenneth AndersonSep 2, 2025
  If you experience flashback (fire in burner tube(s)) in your Kenmore Grill, it's likely because the burner and/or burner tubes are blocked. Turn the knobs to OFF and clean the burner and/or burner tubes. See the burner cleaning section on page 10 of the Use and Care.
P
parsonsclintonSep 4, 2025
What to do if my Kenmore PG-40611S0L Grill won't fill the LP tank?
- V
  Vincent GreerSep 4, 2025
  If you are unable to fill the LP tank for your Kenmore Grill, it may be because some dealers have older fill nozzles with worn threads. These worn nozzles might not have enough “bite” to engage the valve. Try a second LP dealer.
M
Madison KiddSep 6, 2025
How to fix one Kenmore PG-40611S0L burner not lighting from other burners?
- R
  Robert CarterSep 6, 2025
  If one burner on your Kenmore Grill does not light from other burners, it's likely due to drip buildup or food particles in the end(s) of carryover tube(s). Clean the carry-over tube(s) with a wire brush.
T
Tammy AustinSep 9, 2025
What to do if no sparks appear at any electrodes when control knob is turned to HI and noise can be heard from the spark module on Kenmore PG-40611S0L?
- V
  vanessa18Sep 9, 2025
  If no sparks appear at any electrodes when the control knob is turned to HI, but noise can be heard from the spark module on your Kenmore Grill, the electrodes may not be connected properly. Remove and reconnect all electrode wires from the module sockets.

Kenmore PG-40611S0L Specifications

General

Brand	Kenmore
Model	PG-40611S0L
Category	Grill
Fuel Type	Propane
Number of Burners	4
Material	Stainless Steel
Dimensions	52.76 in (W) x 22.05 in (D) x 46.46 in (H)
Weight	88 lbs
Side Burner	Yes
Burner Count	4
Ignition Type	Electronic