Need help?Do you have a question about the Kenwood DMF-9020 and is the answer not in the manual?
Digital Audio System| playing rotation | Approx. 400 rpm ~ 900 rpm (CLV) |
|---|---|
| frequency response (playback mode) | 8 Hz ~ 20 kHz (± 1 dB) |
| signal to noise ratio (playback mode) | More than 112 dB |
D/A and A/D Conversion| D/A conversion | 1 Bit (24 bit type) |
|---|---|
| oversampling | 8 fs (352.8 kHz) |
| A/D converter | 4th order sigma-delta conversion+ D.R.I.V.E. conversion |
Input and Output| analog input sensitivity / input impedance | 500 mV / 22 kW |
|---|---|
| analog output level / output impedance | 2.0 V / Less than 300 W |
| headphone output | 50 mW/32 W load (Phones level MAX) |
General Specifications| power consumption | 20 W |
|---|---|
| dimensions | W: 440 mm, H: 125 mm, D: 373 mm |
| weight (net) | 5.4 kg (11.9 lb) |
Details unit operation voltage for different regions and safety precautions for UK mains plug.
General safety warnings, including electric shock and laser product warnings.
Precautions against lightning surges and proximity to power lines to prevent hazards.
Conditions requiring qualified service and guidelines for connecting equipment to AC outlets and avoiding overloading.
Procedure for preparing the unit for transportation and measures to prevent dust entry.
Instructions for cleaning the unit and avoiding contact cleaners.
Notes on condensation issues and the duration of memory backup when power is off.
Explanation of the CD TEXT system and its use for copying text data from CDs to MDs.
How to reset the microprocessor to resolve operational issues or erroneous displays.
Details on Kenwood system control modes, remote operation, and optical-fiber cable usage.
Explanation of the D.R.I.V.E.II system and how to use the monitor function as a D/A converter.
Instructions for connecting headphones and explanation of the unit's standby mode.
Step-by-step instructions for loading batteries into the remote control unit.
Preparation steps before playing an MD, including setting the timer switch.
Procedure for playing tracks sequentially from track number 1.
How to select and play a specific track number directly.
How to initiate and cancel random playback mode.
Procedure for ejecting the Mini Disc and how to use the AUTO PAUSE function.
How to select automatic or manual track numbering during recording.
How to monitor input sound and check sampling rates.
How to select and adjust various recording settings using the REC MODE key and JOG DIAL.
How to adjust the digital recording level.
How to set the AUTO CUT and AUTO TIME functions for automatic pausing and track numbering.
How to set auto track number detection levels and fade-in/out times.
How to automatically start recording when sound input exceeds a set level.
How to automatically pause recording when sound drops below a set level or track changes.
How to start recording from approximately 6 seconds before the key press.
Details on adjusting recording modes, levels, and other settings before recording.
How to select between stereo analog (ANALOG) and monaural analog (MONO) input modes.
How to choose between automatic and manual track numbering.
How to adjust the recording level and balance using the main unit controls.
Procedure to start the analog recording process.
How to select the appropriate digital input source (coaxial or optical).
How to enable the fade mode for gradual volume changes at the start and end of tracks.
How to choose between automatic and manual track numbering for digital recording.
How to adjust the recording level for digital sources.
Procedure to start the digital recording process.
How to play the source material before or during recording.
How to synchronize recording with CD playback using system control.
Information on SCMS (Serial Copy Management System) and its effect on digital recording.
Explanation of the sampling rate converter and its compatibility.
Detailed explanation of fade-in and fade-out recording functions.
Procedures for reordering tracks individually or in groups, dividing tracks, and combining adjacent tracks.
Methods for erasing multiple tracks simultaneously or a single track.
How to assign, change, or delete titles for discs and tracks.
How to cancel editing operations and revert to the previous state.
Steps to execute the quick move operation and display messages.
Steps to execute the quick erase operation and display messages.
Information about using preset titles for quick and easy title input.
Explanation of specific keys used for title editing functions.
How to load and display CD text information from a compatible CD player.
Procedure for copying CD text data from a CD to the MD disc.
How to switch between different time display modes (elapsed, remaining, title).
How to switch between normal and wide display modes for the level meter.
How to activate the fade mode for recording with gradual volume changes.
Procedure to reset the microprocessor to restore normal operation in case of malfunction.
Common issues related to the MD standard and their possible causes.
Warning regarding radio frequency energy and FCC compliance for the USA.
Caution regarding hazardous radiation exposure and laser product safety compliance.
To Next Page
