Kenwood KT-54 - User Manual

AM-FM STEREO TUNER
KT-54
INSTRUCTION MANUAL
KENWOOD
For your records
Record the serial number, found on the back of the unit, in
the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial num-
bers whenever you call upon your dealer for information or
service on this product.
Model KT-54 Serial Number
Unpacking
Unpack
the
unit
carefully
and
make
sure
that
all
accessories
and
cables
are
put
aside
so
they
will
not
be
lost.
Examine the unit for any possibility of shipping dam-
age.
If
your
unit
is
damaged
or
fails
to
operate,
notify
your
dealer
immediately.
If
your
unit
was
shipped
to
you
directly,
notify the shipping company without delay. Only the con-
signee
(the
person
or
company
receiving
the
unit)
can
file
a
claim against the carrier for shipping damage.
We recommend that you retain the original carton and pack-
ing materials for use should you transport or ship the unit in
the future.
Before applying power
IMPORTANT!
U.S.A. and Canada
Units shipped to the U.S.A. and Canada are designed
for operation on 120 volts AC only. These units are
not equipped with an AC voltage selector switch and
the discussion of such a switch that follows should be
disregarded.
All other countries
Units shipped to countries other than U.S.A. and Can-
' ada are equipped with an AC voltage selector switch
on the rear panel. Refer to the following paragraph for
the proper setting of this switch.
Rear panel safety precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AC voltage selection
This
unit
operates
on
120
volts
or
220
—
240
volts
AC.
The
AC
voltage
selector
switch
on
the
rear
panel
is
set
to
the
voltage
that
prevails
in
the
area
to
which
the
unit
is
shipped.
Before
connecting
the
power
cord
to
your
AC
outlet,
make
sure
that
the
setting
position
of
this
switch
matches
your
line
voltage.
If
not,
it
must
be
set
to
your
voltage
in
accor-
dance
with
the
following
direction.
Note:
Our warranty does not cover damage caused by excessive fine vol-
tage due to improper setting of the AC voltage selector switch.
120V ~~
Setting Setting
220V-240V ~~
Stopper plate
1-2
Fig. 1
1.
Before
plugging
in
this
unit,
make
sure
that
the
position
of
the
AC
Voltage
Selector
conforms
to
your
line
(mains)
voltage.
If
not,
it
must
be
reset.
See
Fig.
1-1.
2.
To
reset
the
selector,
slide
the
stopper
plate
to
the
oppo-
site
side
with
a
screwdriver
or
other
pointed
tool.
See
Fig.
1-2.
3. Insert the power cord securely. See Fig. 1-3.
WARNING:
TO
PREVENT
FIRE
OR
ELECTRIC
SHOCK,
DO
NOT
EXPOSE
THIS
APPLIANCE
TO
RAIN
OR
MOISTURE.
CAUTION:
TO
REDUCE
THE
RISK
OF
ELECTRIC
SHOCK,
DO
NOT
REMOVE
COVER
(OR
BACK).
NO
USER-SERVICEABLE
PARTS
INSIDE.
REFER
SERVICING
TO
QUALI-
FIED
SERVICE
PERSONNEL.
persons.
The
lightning
flash
with
arrowhead
symbol,
within
an
equilateral
triangle,
is
intended
to
alert
the
user
to
the
presence
of
uninsulated
“dangerous
voltage”
within
the
product's
enclosure;
that
may
be
of
sufficient
magnitude
to
constitute
a
risk
of
electric
shock
to
The
exclamation
point
within
an
equilateral
triangle
is
intended
to
alert
the
user
to
the
presence
of
important
operating
and
maintenance
(servicing)
instructions
in
the
litera-
ture
accompanying
the
appliance.
PRINTED IN JAPAN B50-5580-10 x (K, P, U, M, UE, X, S) (G)
6789101112/87

Kenwood KT-54 Specifications