Kenwood KWL90 - User Manual

Other manuals for Kenwood KWL90

Manual344 pages

Questions and Answers

X
xcameronAug 17, 2025
What to do if my Kenwood KWL90 Food Processor is not operating?
- M
  maria05Aug 17, 2025
  If your Kenwood Food Processor is not operating, make sure that you press the control dial to start it.
J
Jonathon JamesAug 20, 2025
What to do if my Kenwood KWL90 stops and shows error E27?
- A
  alexcraigAug 20, 2025
  If your Kenwood Food Processor stops and displays error message E27, it indicates that the overload protection or overheat system has been activated, possibly due to exceeding the maximum capacity. First, unplug the appliance and check for any obstructions or overloading. If it won't operate, remove some ingredients to reduce the load and try restarting it. If the problem persists, unplug the processor and let it stand for 15 minutes, then plug it back in and restart. If it still doesn't work, no other solution is available.
L
Lindsey SimmonsAug 22, 2025
Why is my slow speed attachment not fitting on my Kenwood KWL90 Food Processor?
- K
  Katherine JohnsonAug 22, 2025
  Your slow speed attachment may not fit on your Kenwood Food Processor if it's not compatible with your model. The attachment must have the KAX twist connection system to fit the outlet. If your attachments feature the Bar Connection System, you'll need to use the KAT002ME adapter to connect them to the Twist Connection System.
J
John LawrenceAug 26, 2025
Why is my Kenwood KWL90 Food Processor vibrating heavily during operation?
- C
  Carlos GarciaAug 26, 2025
  Heavy movement or vibrations during operation of your Kenwood Food Processor can be caused by an uneven load in the bowl, exceeding the maximum capacity, or using the wrong tool or speed. To resolve this, reduce the quantity of food or rearrange it in the bowl and restart the unit. Refer to the relevant program and recommended speed charts to ensure you are using the correct tool and speed.
M
Marie BuchananAug 28, 2025
Why does the whisk knock against the bottom of the Kenwood KWL90 Food Processor bowl?
- S
  Stacey LunaAug 28, 2025
  If the whisk, K-beater, or creaming beater is knocking against the bottom of the Kenwood Food Processor bowl or not reaching the ingredients, the tool is likely at the wrong height and needs adjusting. Adjust the height using a suitable spanner – see “Tool Adjustment” section.
B
Bethany AlvarezAug 30, 2025
Why does the weight change on the display screen of my Kenwood KWL90 Food Processor?
- K
  Kristen HollowayAug 30, 2025
  The weight might change on the display screen of your Kenwood Food Processor because the appliance was moved during operation or the mixer head was raised or lowered. Always place the appliance on a dry, flat, stable surface before weighing. Ensure that the power cable is not under tension. Do not move the appliance while using the weighing function. Zero the display before weighing the next ingredients.
M
michaelmaysSep 2, 2025
What to do if my Kenwood KWL90 display shows a minus reading?
- J
  John MontoyaSep 2, 2025
  If the display screen on your Kenwood Food Processor shows a minus reading, it could be because the display wasn't zeroed, ingredients or the bowl were removed, items are pressed against the appliance, or the appliance is too close to a wall. You can either zero the screen, replace the missing ingredients, or refit the bowl. Also, ensure there are no items pressing against the appliance and that it's not against a wall. Zero the display before weighing the next ingredients.
K
Kristin SmithSep 5, 2025
Why can't I switch quickly between units on my Kenwood Food Processor?
- E
  Elijah SampsonSep 5, 2025
  If you're unable to quickly switch between metric and imperial units on your Kenwood Food Processor, it's likely because the appliance is reconfiguring to display the previously selected unit and measurement. Wait 5 seconds and try again.
A
ascottSep 8, 2025
Why is my Kenwood Food Processor display not registering small quantities?
- R
  rmitchellSep 8, 2025
  If the display screen on your Kenwood Food Processor isn't registering small quantities, it's because the quantity weighed is too small. Use teaspoon or tablespoon measures for very small quantities.
M
Mrs. Emily RossSep 12, 2025
Why slow speed attachment cannot be fitted to Kenwood KWL90 Food Processor?
- H
  Helen SimpsonSep 12, 2025
  The slow speed attachment might not fit on your Kenwood Food Processor if it's not compatible with your model. The attachment must have the KAX twist connection system to fit the outlet.