Keysight Technologies PNA-L N5230A

32
For devices with 7 mm connectors
Mechanical calibration kits
– 85050B standard: DC to 18 GHz.
Includes:
00909-60008 7 mm coax termination
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
85050-80011 7 mm sliding load
– 85050C precision TRL: DC to 18 GHz.
Includes:
00909-60008 7 mm coax termination
85050-60003 7 mm to 7 mm airline
85050-60005 7 mm to 7 mm TRL adapter
85050-60006 7 mm fixed broadband load
85050-80008 7 mm short
85050-80009 7 mm short collet
85050-80010 7 mm open
– 85050D economy: DC to 18 GHz.
Includes:
85050-60006 7 mm fixed broadband load
85050-80007 7 mm short
85050-80010 7 mm open
Electronic calibration kits
– N4696B Microwave ECal: 300 kHz to 18 GHz, 2 ports,
7mm to 7mm Microwave module
Cables
1
– 85132C single, semi-rigid: 7 mm to 3.5 mm (f), 81 cm,
32 inches
2
– 85132D set, semi-rigid: two 3.5 mm (f) to 7 mm cables,
53 cm each, 21 inches each
2
, p/n 85132-60003
– 85132E single, flexible: 7 mm to 3.5 mm (f), 97.2 cm, 38.25 inches
2
– 85132F set, flexible: two 3.5 mm (f) to 7 mm cables, 62.9 cm each,
24.75 inches each
2
, p/n 85132-60004
– 85135C single, semi-rigid: 7 mm to 2.4 mm (f), 81 cm, 32 inches
– 85135D set, semi-rigid: two 2.4 mm (f) to 7 mm cables, 53 cm
each, 21 inches each, p/n 85135-60001
– 85135E single, flexible: 7 mm to 2.4 mm (f), 96 cm, 38 inches
– 85135F set, flexible: two 2.4 mm (f) to 7 mm cables, 53 cm each, 21
inches each, p/n 85135-60002
Adapter sets
– 85130E 2.4 mm
1
to 7 mm
For devices with waveguide
Mechanical calibration kits
X Band
– X11644A standard, WR-90: 8.2 to 12.4 GHz.
Includes:
00896-60008 X-band standard section
00910-60003 X-band termination
11644-20018 X-band short
11644-20021 X-band shim
– 85132F cable set (set, flexible 7 mm to 3.5 mm, 62.9 cm each,
24.75 inches each
2
)
– 85135F cable set (set, flexible, 7 mm to 2.4 mm, 53 cm each,
21 inches each)
– X281C adapter (included in calibration kit):
WR-90 to 7 mm
P Band
– P11644A standard, WR-62: 12.4 to 18 GHz.
Includes:
00896-60007 P-band standard section
00910-60002 P-band termination
11644-20017 P-band short
11644-20020 P-band shim
– 85132F cable set (set, flexible, 7 mm to 3.5 mm, 62.9 cm each,
24.75 inches each
2
)
– 85135F cable set (set, flexible, 7 mm to 2.4 mm, 53 cm each,
21 inches each)
– P281C adapter (included in calibration kit): WR-62 to 7 mm
K Band
– K11644A standard, WR-42: 18 to 26.5 GHz.
Includes:
00896-60006 K-band standard section
00910-60001 K-band termination
11644-20016 K-band short
11644-20019 K-band shim
– 85134F cable set (set, flexible, 3.5 mm to 2.4 mm, 53 cm each, 21
inches each)
– K281C adapter (included in calibration kit): WR-42 to 3.5 mm (f)
Option 012 WR-42 to 3.5 mm (m)
1. Special rugged female connector specically for connecting to the network analyzer
test port, but does not mate with a standard male connector.
2. For use with E8362A or B.