King Technology SPARCO CYCLER User Manual

Screw adapters into each end
of Sparco Cycler.
Tighten turning 1 to 2
revolutions with wrench.
DO NOT OVER TIGHTEN.
Attach the filter section of flex hose
to one hose adapter and the return
section of flex hose to the other hose
adapter with clamps and tighten with
screwdriver.
Above Ground Base Installation
The Sparco Cycler should always be installed between the filter
and pool (or between heater and pool if applicable).
W
a
t
e
r
C
Y
C
L
E
R
M
e
t
e
r
e
d
P
o
o
l
P
u
r
i
f
i
e
r
P
I
P
E
T
H
R
E
A
D
S
E
A
L
A
N
T
P
I
P
E
T
H
R
E
A
D
S
E
A
L
A
N
T
P
I
P
E
T
H
R
E
A
D
S
E
A
L
A
N
T
P
I
P
E
T
H
R
E
A
D
S
E
A
L
A
N
T
Bi-flow valve design allows
water flow in either direction.
TO POOL
PUMP
FILTER
TOE NIPPLE
CHECK
VALVE
BUSHING
HOSE
CLAMP
HOSE
ADAPTER
HOSE
CLAMP
HOSE
ADAPTER
1 1/2" OR 1 1/4"
FLEX HOSE
1 1/2"
X
1 1/2"
X
1 1/4"
HOSE ADAPTER
HOSE
CLAMP
FILTER &
PUMP
THREADED
BUSHINGS
Corrosion Resistant
Check Valve
Isolating the Sparco Cycler by installing a corrosion resistant
check valve is recommended to protect the equipment and
prevent discoloration of pool surface.
TOOLS NEEDED:
Pipe Thread
Sealant
Two Hose Adapters
1 1/2"
X
1 1/2"
X
1 1/4"
Two Sections of
1 1/2" Flex Hose (one
provided with filter)
For better stability, Sparco
Cycler may be mounted on a
base using Phillips pan head
screws.
Screwdriver
Wrench
Two 2" Threaded by
1 1/2" Threaded
Bushings
Following pipe thread sealant
directions, brush sealant on
to Sparco Cycler threads in
both ports.
Brush sealant on the
threads of both bushings. DO
NOT USE TEFLON TAPE as
the threads
on these units
are not suitable
for this use and
leaking or bushing failure
could result.
10
MATERIALS NEEDED:
Two
Hose Clamps
RECOMMENDED:
#10
X
1 1/4" Phillips Pan
Head Screws with
Washers
Brush threaded ends of both
hose adapters and inside of
both bushings with sealant.
4.
5.
6.
7.
8.
1. 2. 3.
TO POOL
W
a
t
e
r
C
Y
C
L
E
R
M
e
t
e
r
e
d
P
o
o
l
P
u
r
i
f
i
e
r
W
a
t
e
r
C
Y
C
L
E
R
M
e
t
e
r
e
d
P
o
o
l
P
u
r
i f
i
e
r
ATTENTION BUILDER:
Call 800-222-0169 for an
In Ground test cap to use at
start-up to ensure proper back
pressure.
AUTOMATIC
WATER
TREATMENT
SYSTEM
AUTOMATI C
WATER
TREATMENT
SYSTEM
Screw a bushing
into each port of
Sparco Cycler and hand
tighten.
Completely tighten turning
1 to 2 revolutions with wrench.
AUTOMATIC
WATER
TREATMENT
SYSTEM
AUTOMATIC
WATER
TREATMENT
SYSTEM

King Technology SPARCO CYCLER Specifications

General

Brand	King Technology
Model	SPARCO CYCLER
Category	Swimming Pool Filter
Language	English