11
PT6500 SERVICE MANUAL
P
2
P
3
P
1
start scanning.
It can be set as: short press: scan, long press OFF.
1. Press the programmable key once to start scanning (it should be
effective in the channel scan list).
2. Press once to quit.
Notes:
there are 8 zones from 0 (default zone) to 7; and there can be as
many as 128 channels in each zone. There are totally 16 scan lists;
you can select any scan list. Every scan list can scan any channels
in different zones (16 channels to the most).
Lone working
Press the button set as lone working to start lone working. This
mode is to ensure the safety of the user while using the transceiver
separately.
It can be set as: short press : personal working, long press OFF.
1. Press the programmable key once to start personal working;
2. Press once again to quit.
Notes:
The lone working is connected with the automotive checking in the
programming software, and will be effective when both are set.
Contact list
Enter the Contact list quickly:
It can be set as: short press: contact list, long press OFF.
1. Press the programmable key once to enter the contact list
Call
2. Press again to enter the content interface of the contact list,
3. Select the options in the contact list with /
4. Press PTT to transmit
5. Press to quit.
It can be set as: short press: instantly select channel 1, long
press OFF.
1. Press the key once to instantaneously select the channel, e.g.
CHANNEL 15
2. Press again to return.
Call 1, 2, 3, or 4
Press the side button programmed as Call 1, 2, 3, or 4 to transmit
the specified code stored in the contact list. Release Call
button, and speak to the microphone to call with the PTT button still
pressed.
It can be set as: short press: Call 1, long press OFF.
1. Press the key once to make a call (within the current channel),
and will quit automatically after the call.
Channel Annunciation
Select or delete the voice annunciation function.
Adjust display contrast
You can adjust the display contrast as per your need.
It can be set as: short press: display contrast, long press OFF.
1. Press the key once, Contrast will be shown,
2. Press / to select the character you need,
3. Press to confirm.
Manual programming
The dealer can open the manual programming rights of channel
frequency set, CTCSS DCS.
Basic operations of programmable keys:
You can set the programmable keys with the key set in PC
software, as follows:
It can be set as: short press: display channel frequency, channel
alias and channel No., long press OFF.
1. Press the key once, display the channel alias, e.g.: CHANNEL 1
,
2. Press it again, the channel frequency will be shown, e.g.:
401.66500
3. Press it a third time the channel alias will be shown, e.g.:
CH 1
It can be set as: short press: Zone, long press OFF.
1. Press the key once, Zone No will be shown,
2. Select zone No. with / ,
3. Press to confirm.
It can be set as: short press: channel lock, long press OFF.
1. Press the key once to perform channel lock, then you can not
choose the channel, CHANNEL 1 will be shown.
2. Press it again to cancel channel lock, CHANNEL 1 will be
shown.
P
2
P
3
P
4
P
2
P
3
P
4
4.3 Parameter Setting (PC Mode)
The radio parameters have been programmed in the factory. The
user can program the radio parameters such as working frequency,
channels, QT/ DQT, auto scanning. We designed a user-friendly
and convenient Chinese/English programming software KSP6500
for users to set parameters on the radio. The programming steps
are as follows:
a Install the programming software KSP6500.
b Connect the radio to the computer serial port with the specified
programming cable (KSPL-09), See Figure 4.1.
RS232serial port
Programming cable
KSPL09
Figure4-1
PC
c Turn on the computer power.
d Turn on the radio power.
e Click the KSP65000 program to run the programming software.
f Click on Read in the KSP65000 main menu to read the radio
parameters into the computer; click on Write to transfer the PC
programming parameters into the radio.
g You can program the following parameters with the KSP6500
software:
1) The RX and TX frequency of each channel;
2) The receiving and transmitting signaling of each channel;
3) Busy channel lockout option;
4) TOT;
5) Squelch level option;
6) Power saving option;
7) 2-tone setting;
8) DTMF setting;
9) Beep tone option;
To Next Page
Loading...
