Why does my Kirisun PT3600 Transceiver battery drain so fast after charging?
If the battery of your Kirisun Transceiver drains quickly after charging, the battery life is likely finished. Please replace it with a new battery pack.
Why does my Kirisun PT3600 Transceiver battery drain so fast?
If your Kirisun Transceiver's battery drains quickly after charging, the battery life may be at its end. Replace it with a new battery pack.
What to do if I cannot program the Kirisun PT3600 parameters normally?
If you're having trouble programming the radio parameters, first check the cable connection to ensure it is correct. If the issue persists, the computer's RS232 serial port output might be abnormal, so check the computer. Also, the external MIC/Speaker jack might have a poor connection, and you should replace the jack.
What to do if my Kirisun Transceiver won't turn on or has no display?
If your Kirisun Transceiver doesn't switch on or the display is blank, the battery power may be insufficient. Please recharge or replace the battery pack. Alternatively, the battery pack may not be installed properly. Please remove the battery pack and install it again.
Why is the communication range of my Kirisun PT3600 Transceiver too short?
If the communication range of your Kirisun Transceiver is too short, make sure the antenna is well connected and is the original supplied one. Also, check if the battery power is in normal state. You can ask your local dealer to adjust the squelch level.
What to do if I hear other voices from non-group members on my Kirisun PT3600 Transceiver channel?
To resolve hearing other voices from non-group members on your Kirisun Transceiver channel, change the CTCSS/DCS signal, and make sure to change the CTCSS/DCS signal of all radios in your group.
Why can't I talk to or hear other group members on my Kirisun PT3600 Transceiver?
If you cannot communicate with other group members on your Kirisun Transceiver, ensure the CTCSS/DCS signal is the same as that of your group members. Also, verify that the radio is within the effective communication range.
What to do if my Kirisun PT3600 won't switch on?
If your Kirisun Transceiver doesn't switch on or the display remains blank after switching on, it could be due to insufficient battery power. Try recharging or replacing the battery pack. Alternatively, the battery pack might not be installed correctly. Remove the battery pack and reinstall it to ensure a proper connection.
Why can't I hear other members on my Kirisun PT3600 Transceiver?
If you cannot communicate with or hear other members on your Kirisun Transceiver, ensure that the CTCSS/DCS signal is the same as that of your group members. Also, consider that the radio might be out of the effective communication range.
What to do if I hear other voices on my Kirisun Transceiver?
If you are hearing voices from non-group members on your Kirisun Transceiver, change the CTCSS/DCS signal. Make sure to change the CTCSS/DCS signal of all radios in your group.
Guidelines for optimal performance and compliance with RF energy exposure limits for occupational use.
Equipment tested and found to comply with FCC rules for digital devices, designed for residential installations.
Instructions for charging the radio battery using the power adapter and charger.
Function of the PTT button for making calls and receiving signals.
Procedure to turn the radio on by rotating the knob clockwise.
Steps to transmit a call by pressing the PTT button and speaking.
Procedure to receive a call by adjusting volume and releasing the PTT button.
Starts or stops scanning through programmed channels.
Details on how scanning resumes after pausing (Time Operate, Carrier Operate).
Prevents continuous transmission and overheating.
Restricts transmission on an occupied channel to avoid interference.
Alerts the user when battery voltage is critically low.
General| Frequency Range | 400-470 MHz |
|---|---|
| Output Power | 5W |
| Battery | Li-Ion |
| Battery Capacity | 2000 mAh |
| Water Resistance | IP54 |
| Channel Spacing | 12.5/25 kHz |
| Operating Voltage | 7.4 V |
| Operating Temperature | -20°C to +60°C |
| Channel Capacity | 16 channels |
To Next Page
