GENERAL INFORMATION
Built-In Single and Double Wall Ovens
n
1-3
KitchenAid Model Numbering System
Single Oven
A. Model/serial/rating plate
Electrical Requirements
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path and the wire guage are in accordance with local
codes.
Check with a qualified electrical installer if you are not sure the
oven is properly grounded.
This oven must be connected to a grounded metal, permanent
wiring system.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/
NFPA 70 – latest edition or CSA Standards C22. 1-94, Canadian
Electrical Code, Part 1 and C22.2 No. O-M91 – latest edition,
and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
Electrical Connection
To properly install your oven, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
■ Oven must be connected to the proper electrical voltage
and frequency as specied on the model/serial/rating plate.
The model/serial/rating plate is located under the control
panel on single ovens and under the control panel on the
upper oven cavity on double ovens. See the following
illustrations.
Double Oven
A. Model/serial/rating plate
■ Models rated from 7.3 to 9.6 kW at 240 volts (5.4 to 7.4 kW at
208 volts) require a separate 40-amp circuit. Models rated at
4.8 kW and below at 240 volts (3.6 kW and below at 208 volts)
require a separate 20-amp circuit.
■ A circuit breaker is recommended.
■ Connect directly to the circuit breaker box (or fused
disconnect) through exible, armored, or nonmetallic
sheathed, copper cable (with grounding wire). See “Make
Electrical Connection” section.
■ Flexible conduit from the oven should be connected directly
to the junction box.
■ Fuse both sides of the line.
■ Do not cut the conduit. The length of conduit provided is for
serviceability of the oven.
■ A UL-listed of CSA-approved conduit connector must be
provided.
■ If the house has aluminum wiring, follow the procedure
below:
1. Connect a section of solid copper wire to the ends
of the exible conduit leads.
2. Connect the aluminum wiring to the added section
of copper wire using special connectors and/or tools
designed and UL-listed for joining copper to aluminum.
Follow the electrical connector manufacturer’s
recommended procedure. Aluminum/copper connection
must conform with local codes and industry-accepted
wiring practices.
For power requirements for models, refer to the following table.
Voltage Single Convect Double Convect
240 VAC
208 VAC
240 VAC
208 VAC
4.1 kW
3.1 kW
17.2 A
15.0 A
8.3 kW
6.3 kW
34.2 A
29.9 A
A
A
ŽŶĨŝŐ&ƵĞů WƌŽĚƵĐƚĚĞƚĂŝů &ĞĂƚƵƌĞƉĂĐŬ ŽůŽƌ
<
<ŝƚĐŚĞŶŝĚ K tĂůůŽǀĞŶ ŽŵďŝŶĂƚŝŽŶ d dŚĞƌŵĂůĐŽŽŬŝŶŐ ϭϬ >ŝƐƉůĂLJ ϰ ϮϰŝŶ ϮϬϭϱ > ůĂĐŬ
ŽƵďůĞ dƌƵĞĐŽŶǀĞĐƚŝŽŶ ϯϬ s&ŝƐƉůĂLJ ϳ ϮϳŝŶ & ϮϬϭϲ d ŝƐĐƵŝƚ
^ ^ŝŶŐůĞ ǀĞŶͲŚĞĂƚƚƌƵĞĐŽŶǀĞĐƚ ϱϬ /ĐŽŶŝĐ>ŝƐƉůĂLJ Ϭ ϯϬŝŶ ' ϮϬϭϳ
^
^ƚĂŝŶůĞƐƐĚŽŽƌ
ǁďůĂĐŬĂďŝŶĞƚ
t tĂƌŵŝŶŐƌĂǁĞƌ ^ ŽŶǀĞĐƚŝŽŶǁƐƚĞĂŵ ϳϬ 'ƌĂƉŚŝĐĂů>ŝƐƉůĂLJ ϲ ϯϲŝŶ
^W ^ƚĂŝŶůĞƐƐ^ƚĞĞů
tWƌŽͲ>ŝŶĞ
ŚĂŶĚůĞ
W ^ƉĞĞĚĐŽŽŬ ϵϬ dŽƵĐŚ'ƌĂƉŚŝĐĂů>
ŝƐƉůĂLJ
^^ ^ƚĂŝŶůĞƐƐ^ƚĞĞů
t, tŚŝƚĞ
< K d ϭϬ ϳ ^^
ϮϳΗ^ƚĂŝŶůĞƐƐ^ƚĞĞů<ŝƚĐŚĞŶŝĚŽƵďůĞKǀĞŶǁŝƚŚdŚĞƌŵĂůŽŽŬŝŶŐΘ>ŝƐƉůĂLJŝŶƚƌŽĚƵĐĞĚŝŶϮϬϭϱ
<ŝƚĐŚĞŶŝĚDŽĚĞůEƵŵďĞƌ^LJƐƚĞŵ
zĞĂƌ
ĂƚĞŐŽƌŝĞ
ƌĂŶĚ ^ŝnjĞ
^Z/>EhDZ ϱ ϰϭ ϬϭϬϬϮ
/s/^/KEZ^WKE^//>/dz
сůĞǀĞůĂŶĚ
zZK&WZKhd/KE
ϱсϮϬϭϱϲсϮϬϭϲϳсϮϬϭϳ
t<K&WZKhd/KE
ϰϭсϰϭƐƚǁĞĞŬ
WZKhd^YhEEhDZ
SERIAL NUMBER SEQUENCE
To Next Page
Loading...
Need help?
General
