What to do if the Klarstein 10013325 Ice Maker device does not work and the ICE FULL light comes on?
If the ICE FULL light is on, it could be due to two reasons. First, the ice basket might be full; remove the ice cubes. Second, the ambient temperature might be too low. Ensure the ambient temperature is above 7°C, then restart the Klarstein Ice Maker.
Why does the Klarstein Ice Maker stop and the WATER LOW light flash?
The Klarstein Ice Maker might stop and the WATER LOW light flashes because there is no water in the water supply. Check the water supply. It could also be due to a damaged or disconnected water inlet valve; check the valve connection or replace it. Finally, the water level sensor might not be in the correct position, in which case you should contact a service agency.
What to do if the Klarstein 10013325 FAULT light flashes rapidly after working?
If the FAULT light flashes rapidly after the Klarstein Ice Maker has been running, it could be due to several reasons: * The turn ice motor may be damaged: contact a service agency for replacement. * The water box may be broken: replace it. * The water box may be blocked by ice cubes: remove the ice cubes.
What to do if WATER LOW light always comes on Klarstein 10013325?
If the WATER LOW light is always on, it indicates that there has been no water supply for more than 24 hours. Stop the Klarstein Ice Maker and restart it once the water supply is ready.
What to do if Klarstein 10013325 Ice Maker device does not work without any lights coming on?
If the Klarstein Ice Maker does not work and no lights are on, it could be due to a power supply issue. Check the power supply to ensure it is properly connected. Also, the power supply voltage may not be correct; in this case, cut off the power supply.
What to do if Klarstein 10013325 device does not work, only switch light comes on?
If your Klarstein Ice Maker device does not work, but only the switch light is on, it may be caused by incorrect power supply voltage. Cut off the power supply. It can also indicate that the PCB board is damaged. In this case, contact a service agency for repair or replacement.
What to do if Klarstein 10013325 Ice Maker device does not work, ICE FULL and FAULT flash together?
If the ICE FULL and FAULT lights flash together, the ICE FULL sensor might be damaged or not connected. Contact a service agency for repair or replacement.
What to do if Klarstein Ice Maker device does not work, FAULT light flashes?
If the FAULT light flashes on your Klarstein Ice Maker, the condenser sensor may be damaged or not running. Contact a service agency for repair or replacement.
Why WATER LOW and ICE FULL flash together or the FAULT flash rapidly on Klarstein 10013325?
When the WATER LOW and ICE FULL lights flash together, or the FAULT light flashes rapidly, it could be due to refrigerant leakage. Contact a service agency for check or replacement. It could also mean the compressor isn't running, or the ambient temperature is below 6°C. Keep the ambient temperature above 7°C and then restart the unit.
What does it mean if FAULT, WATER LOW, ICE FULL three lights flash slowly on Klarstein 10013325 Ice Maker?
If the FAULT, WATER LOW, and ICE FULL lights flash slowly, it indicates that the hall sensor is not in the correct position or is damaged. Contact a service agency for adjustment or replacement. Alternatively, the paddle motor may be damaged, and you should contact a service agency for replacement.
Explains the meaning of indicator lights like ICE FULL, WATER LOW, and FAULT during operation.
Provides crucial advice on device usage, including switching off, cooldown periods, and draining for long-term storage.
General| Product Type | Ice Maker |
|---|---|
| Model Number | 10013325 |
| Brand | Klarstein |
| Ice Production Capacity | 15 kg/24h |
| Ice Cube Shape | Bullet |
| Power Consumption | 150 W |
| Voltage | 220-240 V |
| Frequency | 50 Hz |
| Color | Silver |
| Refrigerant | R600a |
| Ice Cube Size | Large, Small |
| Cycle Time | 6- minutes |
| Water Tank Capacity | 2.2 L |
To Next Page