Klarstein Metrobreeze Las Vegas 12 2G User Manual (English)

Questions and Answers:

R
rodriguezcharlesAug 14, 2025
Why is my Klarstein Metrobreeze Las Vegas 12 2G not working?
- M
  Mr. Melvin WilsonAug 14, 2025
  Your Klarstein Air Conditioner might not be working due to several reasons: there is no electricity, so ensure the mains plug is inserted into the socket and the appliance is switched on. The water tank might be full (the overflow indicator displays „FL“), in which case you should empty it. The ambient temperature might be too low or too high; only use the appliance at temperatures between 7-35 °C (44-95 °F). In cooling mode, the room temperature might be lower than the set temperature, or in heating mode, the room temperature might be higher than the set temperature, so try changing the set temperature. Finally, in dehumidification mode, the ambient temperature might be low, so place the appliance in a room with a room temperature above 17 °C (62 °F).
M
Michael RasmussenAug 17, 2025
How to improve the cooling effect of my Klarstein Metrobreeze Las Vegas 12 2G?
- W
  wisehannahAug 18, 2025
  If your Klarstein Air Conditioner's cooling effect isn't satisfactory, consider these factors: direct sunlight can increase heat, so use curtains to reduce it. Open doors or windows, a lot of people, or other heat sources like fridges can also impact cooling, so close windows and doors, increase the air conditioning power, and remove heat sources if possible. A dirty filter screen can hinder performance, so clean or replace it. Finally, ensure the air inlet or outlet isn't blocked; clear any obstructions and verify correct venting, ensuring the hose isn't bent.
K
Kenneth Wagner MDAug 20, 2025
What to do if my Klarstein Metrobreeze Las Vegas 12 2G Air Conditioner display shows 'FL'?
- S
  Sarah ThomasAug 21, 2025
  If your Klarstein Air Conditioner displays 'FL', it means the internal water tank is full. You should drain the water from the drain port located at the bottom rear of the appliance.
D
davisangelaAug 25, 2025
How to reduce loud noise from my Klarstein Metrobreeze Las Vegas 12 2G Air Conditioner?
- J
  Jaime WalkerAug 25, 2025
  If your Klarstein Air Conditioner is making a lot of noise, it might not be placed on a flat surface. Try putting it on a flat and hard surface to reduce the noise.
B
Bob EnglishAug 27, 2025
Why does the remote control not work for my Klarstein Metrobreeze Las Vegas 12 2G Air Conditioner?
- H
  hansonbenjaminAug 28, 2025
  If the remote control isn't working with your Klarstein Air Conditioner, the distance between the appliance and the remote control might be too far. Ensure that the remote control is used near the unit and points directly toward the remote control receiver.
A
Antonio WeberAug 31, 2025
What to do if the compressor does not work in my Klarstein Air Conditioner?
- W
  whitejamesAug 31, 2025
  If the compressor in your Klarstein Air Conditioner isn't working, the overheat protection might have been activated. Wait for 3 minutes until the temperature is lowered, and then restart the appliance.
E
Elizabeth JohnsonSep 3, 2025
What causes 'others' issues in Klarstein Metrobreeze Las Vegas 12 2G Air Conditioner?
- B
  bjenkinsSep 3, 2025
  For 'others' issues with your Klarstein Air Conditioner: it may be due to anti-freezing protection, so wait until the appliance has defrosted, and operation will resume automatically. High pressure protection might be active; after the gas pressure inside the appliance has returned to normal, the appliance continues to operate automatically.
T
tburgessSep 6, 2025
What does error code E1 mean on a Klarstein Metrobreeze Las Vegas 12 2G Air Conditioner?
- H
  Haley HallSep 6, 2025
  If your Klarstein Air Conditioner shows error code E1, it indicates that the pipe temperature sensor is abnormal. Clean the filters and restart the appliance.
J
Jacob MasseySep 9, 2025
What does error code E2 mean on a Klarstein Metrobreeze Las Vegas 12 2G?
- T
  thomasbergerSep 10, 2025
  If your Klarstein Air Conditioner shows error code E2, it indicates that the room temperature sensor is abnormal. Clean the filters and restart the appliance.