Klipsch SYNERGY Series User Manual

IMPORTANT SAFETY INSTRUCTIONS!
READ these instructions. | KEEP these instructions. | HEED all warnings. | FOLLOW all instructions.
DO NOT use this apparatus near water. | CLEAN ONLY with dry cloth.
DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
DO NOT install near any heat sources such as radiators, hear registers, stoves, or other apparatus
(including amplifiers) that produce heat.
ONLY USE attachments/accessories specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with
liquids, such as vases, are placed on the apparatus.
The exclamation point, within an equillateral triangle, is intended to alert the user to
the presence of important opertating and maintenance (servicing) instructions in the
literature accompanying the product.
The lightning flash with arrowhead symbol within an equillateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock to persons.
WARNING: To reduce the risk of fire/electrical shock, do not expose this apparatus to rain/moisture.
WARNING: No naked flame sources - such as candles - should be placed on the product.
CONNECTING
CONVENTIONAL CONNECTION — Using 16—gauge or larger speaker wire, connect the RED “positive”
(+) terminal of the LEFT speaker to the RED “positive” terminal of your amplifier’s LEFT channel.
Connect the BLACK “negative” (—) terminal of the LEFT speaker to the BLACK “negative” (—)
terminal of your amplifier’s LEFT channel. Repeat this procedure for connecting all remaining
speakers to the appropriate amplifier channels. Refer to Figure 4. Make sure that no bare wires
from any of the connections touch any other terminals as this could casue a short and damage
your equipment.
Some Synergy speaker come with dual binding posts that are connected by a
metal strip. Do not remove this strip or your speakers will not function correctly.
Keep this strip in place and connect your speaker wire to the top set of the
binding posts. It is possible to “Bi-wire” a speaker that has two sets of binding posts.
Please see your receiver’s manual for further instructions.
AMPLIFIER REQUIREMENTS — Klipsch speakers are highly efficient and will
operate easily on a wide variety of amplifiers. All Klipsch speakers are 8-ohm
compatible and can be driven to very high levels with low distortion. Due to the
high output levels Klipsch speaker are capable of reproducing, exercise caution
with the volume control. Excessive volume over long periods can permanently
damage your hearing. Overdriving your amplifier could also damage your speakers.
Check with your dealer to make sure your particular amplifier is best suited to
you application. We want you listening for a lifetime.
CARE AND CLEANING — The only thing you should ever need to do to your speakers
is dust them occasionally. Never apply any abrasive or solvent-based cleaner or any
harsh detergent. You can clean the grilles with the brush attachment of a vacuum
cleaner.
EU COMPLIANCE INFORMATION: Eligible to bear the CE mark, Conforms to European
Union EMC Directive 2004/108/EC.
WEEE NOTICE — Note: This mark applies only to countries within the European Union
(EU) and Norway.
This appliance is labeled in accordance with European Directive
2002/96/EC concerning waste electrical and electronic equipment (WEEE).
This label indicates that this product should not be disposed of with
household waste. It should be deposited at an appropriate facility to enable
recovery and recycling.
PRODUCT REGISTRATION — Register product online at www.klipsch.com/register
• Klipsch will keep you up-to-date on new products and promotions.
• Your personal information will never be resold.
• This registration information is not used for warranty purposes. Please retain your
receipt for warranty claims.

Klipsch SYNERGY Series Specifications

General

Series	SYNERGY
Sensitivity	Check individual model
Impedance	8 ohms
Woofer	Check individual model
Tweeter	Check individual model
Enclosure Type	Check individual model
Dimensions	Check individual model
Weight	Check individual model