Why can't my KNEGT DF504G3 lift anything?
If your KNEGT Tractor cannot lift with either light or heavy loads, it could be due to an oil returning valve blocked at the open position; check and clean the valve. A non-working gear pump requires replenishing oil to the specified level. A seriously blocked filter net needs cleaning or replacement.
Why is my KNEGT Tractor implement shivering during lifting?
If your KNEGT Tractor's hydraulic implement shivers during lifting and experiences fast static sink, it could be due to several reasons. A distributor single direction valve, sink valve, or oil cylinder safety valve may seal poorly, requiring cleaning and repair. The hydraulic output may be jammed, also sealing badly and needing the same attention. A damaged sink speed control valve leaking should be replaced, and a damaged O-ring on the oil cylinder piston leaking should also be replaced.
Why is the brake on my KNEGT DF504G3 not releasing and causing heat?
If your KNEGT Tractor experiences brake drag and overheating, ensure the grip brake is not engaged by loosening it. Also, check and adjust the brake pedals’ free path, as it may be too small.
What causes the front wheels of my KNEGT Tractor to sway?
If your KNEGT Tractor's front wheels are swaying, it could be due to several reasons. A heavily abraded bearing of the front driven axle or steering knuckle needs replacement. Too large a clearance of the front and rear supporting seat requires adjustment. A seriously deformed front wheel rim should be corrected. Improper front wheel toe-in adjustment also needs adjustment.
Why is the clutch slipping on my KNEGT DF504G3 Tractor?
If the clutch on your KNEGT Tractor is slipping, it could be due to several reasons. The clutch disk or plate might be stained with oil; if so, clean them with gasoline and eliminate any oil leakage. Alternatively, the clutch disk may be unevenly or seriously worn, requiring replacement. Insufficient or absent free path could also be the cause, necessitating readjustment. Lastly, a deformed driven disk would need replacing.
Why did the brake on my KNEGT Tractor fail?
If the brake on your KNEGT Tractor fails, it could be due to a seriously or eccentrically worn brake disk, requiring you to put air out of the pipe. Alternatively, an excessively large free path of the brake pedal needs readjustment.
Why does my KNEGT DF504G3 Tractor's starter motor start weakly?
If your KNEGT Tractor's starter motor starts weakly and cannot start the engine, it could be due to several reasons. A seriously abraded bearing with the pivot touching the housing requires bearing replacement. Poor contact between the carbon brush and the collector needs adjustment. If the commutator surface is burnt or stained with oil, clean the oil and grind it with “0” model non-metal sandpaper. Unwell wire connections should be fastened. Burnt out main touch points on the electromagnetic switch with poor contact should be grinded by “0” model non-metal sandpaper. Finally, insufficient battery volume requires recharging.
Why does the gear keep disconnecting on my KNEGT Tractor?
If the gear disconnects itself on your KNEGT Tractor, it might be due to a seriously worn poking fork positioning slot, which requires adjustment or replacement of the poking fork shaft. Insufficient interlock pin spring pressure can be resolved by adjusting or replacing the spring. Also, worn splines on the teeth seat would necessitate replacing the teeth seat.
Why are the bearings of helical bevel pinion and differential shaft overheating in my KNEGT DF504G3?
If the bearings of the helical bevel pinion and differential shaft in your KNEGT Tractor are running at high temperatures, it could be due to excessive pre-tension, which requires adjustment. Another cause could be poor lubrication; check the oil level and replenish if necessary.
Why is my KNEGT Tractor generator not charging properly?
If the generator on your KNEGT Tractor does not charge enough or charges unsteadily, it could be due to a loose transmission V-belt, causing the generator rate to decline; adjust the belt. A loose wire point should be fastened. A broken carbon brush needs checking and repair. A damaged regulator should also be checked and repaired.
Procedures to follow in case of emergencies involving the tractor.
Identifies and explains all tractor instruments and controls.
Instructions on operating the tractor's transmission and driving.
Common clutch problems, their causes, and fixing methods.
Common braking system issues, their causes, and fixing methods.
To Next Page
General
