How to troubleshoot no AC output on a Kohler Inverter?
If your Kohler Inverter has no AC output, first ensure that the AC circuit breaker is in the ON position. If the breaker is tripping, it could be due to an overload; try reducing the load on the generator set. If the breaker trips due to a short circuit or if the engine fuse is blown, contact an authorized Kohler distributor/dealer for service.
What to do if my Kohler Inverter cranks but won't start?
If your Kohler Inverter cranks but doesn't start, starts hard, lacks power, or operates erratically, consider these potential causes: * A clogged air cleaner. Clean and/or replace the air cleaner. * A weak or dead battery. Recharge or replace the battery. * Poor battery connection. Clean and tighten the battery connections. * A loose spark plug wire connection. Check the spark plug wires. * Low oil pressure shutdown. Check for oil leaks and the oil level, adding oil if necessary. * Insufficient fuel pressure. Check the fuel supply and valves. * A blown engine fuse. Replace the fuse; if it blows again, contact an authorized Kohler distributor/dealer. * Engine malfunction. Contact an authorized Kohler distributor/dealer.
How to fix a Kohler Inverter when it does not crank?
If your Kohler Inverter generator set does not crank, it might be due to a weak or dead battery. Try recharging or replacing the battery. Also, check the battery connections to ensure they are properly connected. A blown fuse could also be the culprit, so replace the fuse. If it continues to blow, contact an authorized Kohler distributor/dealer for service. Finally, make sure the generator set is turned on by pressing the RUN button or AUTO for remote starting.
Why is there no AC output from my Kohler Inverter?
If your Kohler Inverter has no AC output, check the following: * Ensure the AC circuit breaker is in the ON position. * If the AC circuit breaker is tripping due to overload, reduce the load on the generator set. * If the AC circuit breaker is tripping because of a short circuit, contact an authorized Kohler distributor/dealer for service. * If the engine fuse is blown, replace it. If the fuse blows repeatedly, contact an authorized Kohler distributor/dealer for service.
How to resolve low output voltage on a Kohler Inverter?
If you're experiencing low output or an excessive drop in voltage with your Kohler Inverter, it could be that the generator set is overloaded. Try reducing the load.
What causes loss of communication to accessory modules in a Kohler 38RCLA Inverter?
Loss of communication to accessory modules in your Kohler Inverter can be caused by: * Bad connections. Check wiring and connections. Verify that cable size and length of run comply with the instructions in the Installation manual. * Low or no battery voltage. Check battery connections and the generator set battery.
Why does my Kohler 38RCLA generator set stop suddenly?
Your Kohler Inverter generator set may stop suddenly due to several reasons: * Low oil pressure shutdown. Check for oil leaks and the oil level, adding oil if necessary. * Being out of fuel. Check fuel supply. * Overcrank shutdown. Reset the controller. If the overcrank fault occurs again, contact an authorized Kohler distributor/dealer. * Blown fuse(s). Replace the fuse. If the fuse blows again, contact an authorized Kohler distributor/dealer. * Overspeed shutdown. Reset the controller. If the overspeed fault occurs again, contact an authorized Kohler distributor/dealer. * The generator set is OFF. Press the RUN button to start the engine or press AUTO to allow remote starting. * Remote stop command received from a remote switch, ATS, or OnCuer. Check the remote switch posi...
What causes low output voltage on a Kohler Inverter?
If your Kohler Inverter experiences low output or excessive voltage drop, it might be overloaded. Try reducing the load on the generator set.
How to fix all electric fans that are not operating in Kohler Inverter?
If all electric fans in your Kohler Inverter are not working, check the fan fuses. Also, verify that the fan system's positive power supply is correctly connected to the positive (+) battery terminal.
What to do if Kohler Inverter fan does not transition to high-speed at threshold temperature?
If the fan in your Kohler Inverter isn't switching to high speed when it reaches the threshold temperature, start by checking the sensor's function. Inspect the harnesses from the fuse/relay terminal block to the fans and controller for any damaged leads or terminations. Evaluate the relays for proper operation, check the coil's continuity, and verify the transition at the threshold temperatures.
General| Model | 38RCLA |
|---|---|
| kW Rating (LP) | 38 kW |
| kW Rating (NG) | 38 kW |
| Voltage | 120/240V |
| Starting System | Electric Start |
| Cooling System | Air-cooled |
| Fuel Type | Natural Gas |
| Phase | Single Phase |
| Alternator | Brushless |
| Warranty | 5 years |
To Next Page