Kohler 60RCL User Manual (English)

Other manuals for Kohler 60RCL

Manual112 pages

Operation72 pages

Questions and Answers:

L
Lorraine MartinezAug 21, 2025
How to fix a Kohler 60RCL Inverter generator that won't crank?
- G
  garciajohnAug 21, 2025
  If your Kohler Inverter generator won't crank, there are several potential causes: * The battery may be weak or dead. Recharge or replace the battery. * The battery connections might be reversed or poor. Check the connections. * A fuse may be blown. Replace the fuse; if it blows repeatedly, contact an authorized Kohler distributor/dealer for service. * The generator set may be OFF. Press the RUN button to start the engine or press AUTO to allow remote starting.
S
Scott WilkinsonAug 23, 2025
What to do if my Kohler 60RCL Inverter cranks but won't start?
- K
  Kara LevineAug 23, 2025
  If your Kohler Inverter cranks but doesn't start, starts hard, lacks power, or operates erratically, consider these potential causes: * A clogged air cleaner. Clean and/or replace the air cleaner. * A weak or dead battery. Recharge or replace the battery. * Poor battery connection. Clean and tighten the battery connections. * A loose spark plug wire connection. Check the spark plug wires. * Low oil pressure shutdown. Check for oil leaks and the oil level, adding oil if necessary. * Insufficient fuel pressure. Check the fuel supply and valves. * A blown engine fuse. Replace the fuse; if it blows again, contact an authorized Kohler distributor/dealer. * Engine malfunction. Contact an authorized Kohler distributor/dealer.
D
Daniel WareAug 25, 2025
How to fix a Kohler Inverter when it does not crank?
- S
  stephanie01Aug 26, 2025
  If your Kohler Inverter generator set does not crank, it might be due to a weak or dead battery. Try recharging or replacing the battery. Also, check the battery connections to ensure they are properly connected. A blown fuse could also be the culprit, so replace the fuse. If it continues to blow, contact an authorized Kohler distributor/dealer for service. Finally, make sure the generator set is turned on by pressing the RUN button or AUTO for remote starting.
P
Pamela TurnerAug 28, 2025
Why is there no AC output from my Kohler 60RCL?
- T
  Theresa VangAug 28, 2025
  If your Kohler Inverter has no AC output, check the following: * Ensure the AC circuit breaker is in the ON position. * If the AC circuit breaker is tripping due to overload, reduce the load on the generator set. * If the AC circuit breaker is tripping because of a short circuit, contact an authorized Kohler distributor/dealer for service. * If the engine fuse is blown, replace it. If the fuse blows repeatedly, contact an authorized Kohler distributor/dealer for service.
M
Matthew RiveraAug 31, 2025
How to resolve low output voltage on a Kohler 60RCL?
- K
  Kevin CookAug 31, 2025
  If you're experiencing low output or an excessive drop in voltage with your Kohler Inverter, it could be that the generator set is overloaded. Try reducing the load.
Q
qthompsonSep 1, 2025
What causes loss of communication to accessory modules in a Kohler Inverter?
- M
  matthewmillerSep 1, 2025
  Loss of communication to accessory modules in your Kohler Inverter can be caused by: * Bad connections. Check wiring and connections. Verify that cable size and length of run comply with the instructions in the Installation manual. * Low or no battery voltage. Check battery connections and the generator set battery.
E
Elizabeth RiceSep 3, 2025
What to do if the LCD display is off on my Kohler 60RCL controller?
- S
  Samuel AlvarezSep 3, 2025
  If the LCD display is off on your Kohler Inverter controller, it may be due to low or no battery voltage. Check connections and the generator set battery.
C
Christopher FuentesSep 4, 2025
Why is the date flashing on my Kohler 60RCL Inverter display?
- P
  Paula ChaneySep 5, 2025
  The date flashes on your Kohler Inverter display when the controller power was disconnected and then reconnected. Check battery connections. Check utility power connection for the built-in battery charger. Reset the time, date, and exercise schedule.
C
Carrie AndrewsSep 6, 2025
Why do my Kohler Inverter fans operate in high-speed mode continuously?
- D
  Debra HowardSep 6, 2025
  If the fans in your Kohler Inverter are constantly running at high speed, examine the radiator and enclosure openings to ensure there's no blockage restricting airflow. Also, verify the sensor's functionality. Inspect the harnesses from the fuse/relay terminal block to the fans and controller for any damaged leads or terminations. Evaluate the relays for proper operation, check the coil's continuity, and confirm the transition at the specified threshold temperatures.
R
Rebecca HardySep 8, 2025
What to do if Kohler Inverter fan does not transition to high-speed at threshold temperature?
- C
  cnicholsSep 8, 2025
  If the fan in your Kohler Inverter isn't switching to high speed when it reaches the threshold temperature, start by checking the sensor's function. Inspect the harnesses from the fuse/relay terminal block to the fans and controller for any damaged leads or terminations. Evaluate the relays for proper operation, check the coil's continuity, and verify the transition at the threshold temperatures.