Kohler COMMAND CV17-745 - Page 13

1.11
Section 1
Safety and General Information
Crankcase cont.
Oil Drain Plug Torque ..................................................................................13.6 N·m (10 ft. lb.)
Oil Pan
Oil Pan Fastener Torque.............................................................................24.4 N·m (216 in. lb.)
Crankshaft
End Play (Free) ..........................................................................................0.070/0.590 mm (0.0028/0.0230 in.)
Crankshaft Bore (In Crankcase)
New......................................................................................................40.965/41.003 mm (1.6128/1.6143 in.)
Max. Wear Limit ...................................................................................41.016 mm (1.6148 in.)
Crankshaft to Sleeve Bearing (Crankcase)
Running Clearance - New ....................................................................0.03/0.09 mm (0.0012/0.0035 in.)
Crankshaft Bore (In Oil Pan) - New ............................................................40.987/40.974 mm (1.6136/1.6131 in.)
Crankshaft Bore (In Oil Pan)-to-Crankshaft
Running Clearance - New ....................................................................0.039/0.074 mm (0.0015/0.0029 in.)
Flywheel End Main Bearing Journal
O.D. - New ...........................................................................................40.913/40.935 mm (1.6107/1.6116 in.)
O.D. - Max. Wear Limit ........................................................................40.84 mm (1.608 in.)
Max. Taper ...........................................................................................0.022 mm (0.0009 in.)
Max. Out-of-Round ..............................................................................0.025 mm (0.0010 in.)
Oil Pan End Main Bearing Journal
O.D. - New ...........................................................................................40.913/40.935 mm (1.6107/1.6116 in.)
O.D. - Max. Wear Limit ........................................................................40.84 mm (1.608 in.)
Max. Taper ...........................................................................................0.022 mm (0.0009 in.)
Max. Out-of-Round ..............................................................................0.025 mm (0.0010 in.)
Connecting Rod Journal
O.D. - New ...........................................................................................35.955/35.973 mm (1.4156/1.4163 in.)
O.D. - Max. Wear Limit ........................................................................35.94 mm (1.415 in.)
Max. Taper ...........................................................................................0.018 mm (0.0007 in.)
Max. Out-of-Round ..............................................................................0.025 mm (0.0010 in.)
Crankshaft T.I.R.
PTO End, Crank in Engine ...................................................................0.279 mm (0.0110 in.)
Entire Crank, in V-Blocks .....................................................................0.10 mm (0.0039 in.)
Cylinder Bore
Cylinder Bore I.D.
New - CV17 ..........................................................................................73.006/73.031 mm (2.8742/2.8752 in.)
New - CV18, CV20, CV22 (624 cc) .......................................................77.000/77.025 mm (3.0315/3.0325 in.)
New - CV22/23 (674 cc) .......................................................................80.000/80.025 mm (3.1496/3.1506 in.)
New - CV25, CV26, CV730-745 ............................................................82.988/83.013 mm (3.2672/3.2682 in.)
Max. Wear Limit - CV17 .......................................................................73.070 mm (2.8757 in.)
Max. Wear Limit - CV18, CV20, CV22 (624 cc) ....................................77.063 mm (3.0340 in.)
Max. Wear Limit - CV22/23 (674 cc) ....................................................80.065 mm (3.1522 in.)
Max. Wear Limit - CV25, CV26, CV730-745 .........................................83.051 mm (3.2697 in.)
Max. Out-of-Round CV17 ...................................................................... 0.13 mm (0.0051 in.)
Max. Out-of-Round CV18-745 ...............................................................0.12 mm (0.0047 in.)
Kohler Engine Parts Call K&T 606-678-9623 or 606-561-4983
www.mymowerparts.com