Korg BX-3 - Page 32

Parameters
32
MIDI Rx C. Change (MIDI Receive Control Change)
[Dis, Ena]
Dis (Disable): Incoming MIDI control changes will be
ignored.
Ena (Enable): Incoming MIDI control changes will be
received. (The factory setting is Ena.)
MIDI Tx C. Change (MIDI Transmit Control Change)
[Dis, Ena]
Dis (Disable): MIDI control changes will not be transmit-
ted.
Ena (Enable): MIDI control changes will be transmitted.
(The factory setting is Ena.)
MIDI Local Cntrl (MIDI Local Control) [Off, On]
Turns local control on/off. (The factory setting is On.)
Off: The keyboard will be internally disconnected from
the tone generator section. Select this setting when you
want to use the keyboard and controllers of the BX-3 only
to play a different tone generator.
○ ○○○○○○○○○○○○○○○○○○○○○
Group 4: MIDI CC# 1
CC# Upper DB Sel (MIDI CC# Upper Drawbar Select)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the UPPER setting of the
DRAWBAR SELECT section. (The factory setting is 79.)
CC# Lower DB Sel (MIDI CC# Lower Drawbar Select)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the LOWER setting of the
DRAWBAR SELECT section. (The factory setting is 80.)
CC# Drawbar 1 16’ (MIDI CC# Drawbar 1–16’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 16' setting of Drawbar 1.
(The factory setting is 16.)
CC# Drawbar 1 5
1
/3’(MIDI CC# Drawbar 1–5-1/3’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 5-1/3' setting of Drawbar
1. (The factory setting is 17.)
CC# Drawbar 1 8’(MIDI CC# Drawbar 1–8’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 8' setting of Drawbar 1.
(The factory setting is 18.)
CC# Drawbar 1 4’(MIDI CC# Drawbar 1–4’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 4' setting of Drawbar 1.
(The factory setting is 19.)
CC# Drawbar 1 2
2
/3’(MIDI CC# Drawbar 1–2-2/3’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 2-2/3' setting of Drawbar
1. (The factory setting is 20.)
CC# Drawbar 1 2’(MIDI CC# Drawbar 1–2’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 2' setting of Drawbar 1.
(The factory setting is 21.)
CC# Drawbar 1 1
3
/5’(MIDI CC# Drawbar 1–1-3/5’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 1-3/5' setting of Drawbar
1. (The factory setting is 22.)
CC# Drawbar 1 1
1
/3’(MIDI CC# Drawbar 1–1-1/3’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 1-1/3' setting of Drawbar
1. (The factory setting is 23.)
CC# Drawbar 1 1’(MIDI CC# Drawbar 1–1’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 1' setting of Drawbar 1.
(The factory setting is 24.)
CC# Drawbar 2 16’(MIDI CC# Drawbar 2–16’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 16' setting of Drawbar 2.
(The factory setting is 70.)
CC# Drawbar 2 5
1
/3’(MIDI CC# Drawbar 2–5-1/3’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 5-1/3' setting of Drawbar
2. (The factory setting is 71.)
CC# Drawbar 2 8’(MIDI CC# Drawbar 2–8’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 8' setting of Drawbar 2.
(The factory setting is 72.)
CC# Drawbar 2 4’(MIDI CC# Drawbar 2–4’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 4' setting of Drawbar 2.
(The factory setting is 73.)
CC# Drawbar 2 2
2
/3’(MIDI CC# Drawbar 2–2-2/3’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 2-2/3' setting of Drawbar
2. (The factory setting is 74.)
CC# Drawbar 2 2’(MIDI CC# Drawbar 2–2’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 2' setting of Drawbar 2.
(The factory setting is 75.)
CC# Drawbar 2 1
3
/5’(MIDI CC# Drawbar 2–1-3/5’)
[1...31, 33...95, Off]
Specifies the MIDI control change number that will be
used to transmit and receive the 1-3/5' setting of Drawbar
2. (The factory setting is 76.)